Engine Bay Parts

 

021256325A 021256326A Heater blower plate gasket kit

021256325A 021256326A Heater blower plate gasket kit

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256325A Heater blower plate gasket (Right)

021256325A Heater blower plate gasket (Right)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256326A Heater blower plate gasket (Left)

021256326A Heater blower plate gasket (Left)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

914.424.075.03 914 heater cable for 75-76

914.424.075.03 914 heater cable for 75-76

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

PCG42407501 914 heater cable for 914/6

PCG42407501 914 heater cable for 914/6

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

Porsche 914 heater cable nipple Set

Porsche 914 heater cable nipple Set

This listing is for a set of 2 heater cable covers or "nipples" that keep water from getting into the center tunnel from the firewall side. Most of these have baked out as they were made from organic rubber. I have made these from a higher temp...

Throttle body gasket for 1.7 intake

Throttle body gasket for 1.7 intake

This is a NLA gasket available only here only $10.50

1.7 intake hose 022 129 967 With lip for oil bath or without

1.7 intake hose 022 129 967 With lip for oil bath or without

This is the 1.7 intake taht is set up to re sue the metal hardware for the oil bath set up. or to utilize a clamp for the non oil bath air filter. If you are in doubt you can select the oil bath and it can be trimmed off. I was asked to make...

1.8 Throttle body seal for intake

1.8 Throttle body seal for intake

This is the throttle body gasket for the 1.8 intake. I've made the 1.7 for years and finally the 1.8 as a number of you have been asking for these, as NOS is hard to find.

2.0L Throttle Body to Plenum Seal

2.0L Throttle Body to Plenum Seal

NLA from factory, this is the 2.0L Throttle Body to Plenum Rubber Sleeve. Molded with the hose clamp stop in it just like OEM.

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

This is a reproduction of early rain tray. These are more sturdy than the OEM ones as the material has a higher melting point and is thicker. Don't forget the rubber bumper that keeps the rear trunk lid from hitting this. I have them reproduced...

Late Rain tray 91451218910

Late Rain tray 91451218910

This is our reproduction of the rain trays that keep your engine compartment from getting wet. They superceeded the early version (which we also make), and look identical to factory. We did however make them slightly thicker and out of a better...

Engine bay rain tube funnel Grommets set of 2 914.572.913.10

Engine bay rain tube funnel Grommets set of 2 914.572.913.10

These are the funnel tube grommets that hold the tube in place on the sheetmetal. These are made from silicone so that they should hold up a little better that the OEM version. These NLA pieces will dress up your engine shelf nicely, why reuse your crusty old rubber ones if you don't have to?

Rain tray drain tubes set of 2 PCG 571 900 00

Rain tray drain tubes set of 2 PCG 571 900 00

This is a set of drain tubes that are needed to allow the water to drain from the rain tray through the engine compartment. The funnels and grommets are not included with these. It is not 100% correct for the OEM hose, butismuch c,oser than the...

914 injector covers (set of 4) 311906102

914 injector covers (set of 4)  311906102

Injector covers to replace your torn or worn out covers. Your wiring will thank you.

914 rear sway bar bushing set of 2 90133379304

914 rear sway bar bushing set of 2 90133379304

These are the new thermally enhanced rear sway bar bushings, I include both, think about it, do you really only want to replace one? These have been NLA for quite some time and I have been hand casting these. The quality is vastly improved. The...

914 Transmission tail cone gasket

914 Transmission tail cone gasket

This is the gasket you need to remove the tail cone and reinstall. If you don't want to pay for an entire kit you can get just the one you need.

914 Valve Cover Gaskets - Set of 2

914 Valve Cover Gaskets - Set of 2

This is an improved version the OEM part. Over time the bales on the valve covers loose tension. These are made from a similar material that is slightly thicker and denser to create a good tight seal.

914.424.591.00 Parking brake sealing bellows - Set of 2

914.424.591.00 Parking brake sealing bellows - Set of 2

This i sthe barking barake bellows that the OEM one disolves in brake fluid. Now you can replace this hard to find part, inexpensively. This is a set of 2, because if you are missing one, you probably need or will need another soon.

914/6 dipstick for fender oil cooler

914/6 dipstick for fender oil cooler

Thsi is a replica of the factory 914/6 dipstick for the offset oils cooler in the fenderwell. They are not identical to factory close. We hand made each of these. Will start shipping 7/14/14 More pictues will be added as soon as they are back from finishing.

914/6 Stainless fuel rail

914/6 Stainless fuel rail

These are made at the request of a 914/6 owner that wanted the correct rail reproduced in stainless. they have been flow and pressure tested to meet (actually exceed) flow rates and pressures compared to the OEM. We may be out from time to time...

45 Degree Rubber Sleeve for Fuel Line

45 Degree Rubber Sleeve for Fuel Line

This grommet goes in the engine compartment tin where the fuel line passes through the the tin.

Fuel line grommet 10mm

Fuel line grommet 10mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Fuel line grommet 8mm

Fuel line grommet 8mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Alternator Inspection Cover

Alternator Inspection Cover

Plastic cover for the fan housing to allow access to the alternator top bolt. For adjustment with engine installed. Helps keep airflow directed for cooling.

914 Alternator harness grommet

914 Alternator harness grommet

These are the grommets that go on the wirring harness at the tin behind the alternator, and at the sheetmetal on the engine. This is for one grommet.

Alternator wiring harness 70-76 4 cylinder only plug and play

Alternator wiring harness 70-76 4 cylinder only plug and play

This is a direct replacement fro your old worn out wirring harness. If you replace your alternator you more than likely will need the rubber, now you can eliminate any potential problems by simply replacing. Correct gage wires used along with new...

(1)

Battery block positive terminal - optional hardware and stud

Battery block positive terminal - optional hardware and stud

This is the NLA battery block that is used on the positive terminal. It's NLA but you can get one here inexpensively. The current configuration allows for the option to add the stud and hardware if you do not have them.They do not come with unless you use the option to add them.

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Cooling flap bushings for use on 911, and type 4 engines

Brake light / Trans reverse light switch cover 914.613.491.00

Brake light / Trans reverse light switch cover 914.613.491.00

This is the same boot for both application. Fits all years. These are currently availabe at over $20 each. Mine have the correct retaining grove at the base to make a good seal. Save yourself a bunch of cash and get a well made part. These are in...

Clutch cable end (trunion), bellows, 2 nuts, pulley and bushing

Clutch cable end (trunion), bellows, 2 nuts, pulley and bushing

This is a package that includes the Clutch cable end that attaches to the throwout bearing arm, the bellows that keeps crud out of the cable tube, the pulley, pulley bushing and 2 correct nuts to set tension. Others will sell you a nylock nut. It...

Porsche 914 Clutch Cable Bellows 914.423.922.02

Porsche 914 Clutch Cable Bellows 914.423.922.02

Clucth cable bellows replace your old mangled or missing bellows for a fraction of the cost others charge. High quality.

Clutch Cable M7 Hexagon Nut - Stainless Steel

Clutch Cable M7 Hexagon Nut - Stainless Steel

This is the correct nut for your clutch cable. I recomend using 2 tightened against each other to lock them in place. Many have used Nylock nuts to replace the onle ones. I had a bad experiece where on a hot day mine got warm enough when I was...

Clutch cable trunion 911.423.205.03

Clutch cable trunion 911.423.205.03

This is for the glod plated clevis that the clutch cable slides through brand new now $6 all day long.

Cover cap for adjuster cover on ECU box

Cover cap for adjuster cover on ECU box

I didn't even know mine was missing until I checked. These are not being shown as available alone, so no suprice when they got lost or damaged they were never replaced. These are so inexpensive you almost can't afford not to. Yes the last picture...

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

This is a reproduction cylinder head temperature sensor that is construcetd from stainles steel. Utilizing tested internal componets that have been used to replace these (Original Customs was originally remanufacturing these). Now you can replace...

Early style relay board cover 914.610.111.13 Correct for 6

Early style relay board cover 914.610.111.13 Correct for 6

This is the correct style relay board cover of the early car with NON retractable seat belts. Others have made copies of the late style that has the slope, as they will fit all cars. We went the other way and made the harder to find early cover....

Early Trans Rubber Bellows and Band for Plastic Housing

Early Trans Rubber Bellows and Band for Plastic Housing

 This is a set of both the band at the housing to firewall and the bellows on the firewall housing.

Parts 914.424.502.00 and 914.424.297.00

Engine Deck Lid Bumper Set 914.559.253.10

Engine Deck Lid Bumper Set 914.559.253.10

These are the long sought after engine deck lid bumpers that are NLA. You can get them here and inexpensively.

 

Engine parts package

Engine parts package

Engine kit -Set of all 4 engine seals, the heater grommets in sheet metal, set of 50 stainless engine tin allen head screws with washers, 2 alternator harness grommets, 2 heater cable nipples, and set of heater hoses 

914.424.224.03 late side shifter Firewall bushing

914.424.224.03 late side shifter Firewall bushing

This is the firewall bushing that will take some of the slop out of your shifting. Normally these are difficult to install, but we have made some changes that will allow for easy installation. We I decided to make these just like the small...

901.741.291.00 Tail shift sealing sleeve #50 on the PET

901.741.291.00 Tail shift sealing sleeve #50 on the PET

This is the rear sealling bellows for the early side shift transmission. PET catalog shows part as 901.741.291.00. Interestingly enough others reference this as Speedometer Cable Boot Fits 911, 1965-1971. This was reproduced off a stock 914 part...

Early side shift firewall to housing gasket

Early side shift firewall to housing gasket

This is the tail shift gasket that holds the plastic housing to the firewall. This is only the "band" at the firewall.

 914.424.502.00

Late Side Shift Bushing Kit

Late Side Shift Bushing Kit

Get everything you need to eliminate sloppy shifting in one kit, with the option to add the shift housing cover for only $12 more. Kit consists of: 911.424.139.00 911.424.223.03 (x2), 911.424.224.02, 911.424.224.03, and 914 424 239 02.

Late side shifter bushing for transmission mount 914.424.224.02

Late side shifter bushing for transmission mount 914.424.224.02

This is the bushing that installs at the mount on the transmission to guide the lever for a more solid shift.

914 late side shifter bellows

914 late side shifter bellows

Yes 2 are shown, but you only need one. This is the bellows that goes at the rear of the shift linkage and keeps crud from getting into the shifter housing (the black plastic cup).

They were NLA, but you can get them here.

Side shift 914 and 911 knuckle bushings set 911 424 223 03

Side shift 914 and 911 knuckle bushings set 911 424 223 03

These are the bushings for the late coupler on the side shift linkage. These are toleranced correctly so they fit snug and are easier to install. Looks like these are part # 911.424.223.03. I had ordered new from factory and they were sloppy....

PCG 424.501.01 Late side shifter cover

PCG 424.501.01 Late side shifter cover

This is the cover that keep the crud from gettining into the shift mechanism atthe rear of the linkage. It mounts onto a plate atthe transmission. It is a nice part to finish off your underside ans it's nice and glossy. It is also flexable...

Oil cooler and tin gasket 021119329

Oil cooler and tin gasket 021119329

Another NLA part we all need. This gasket goes on the engine tin and seals the gap between the cooler and the tin.  Made from silicone to offer a better seal. It also acts as a buffer between the two.

Now available at a reasonable price.

Throttle Position Sensor Board Early 1.7 ONLY: 1970-1971

Throttle Position Sensor Board Early 1.7 ONLY: 1970-1971

This is the throttle position sensor board for the early 1.7 TPS. It will only work on the early (70-71) TPS, as they are quite diferent from the late.

Porsche 914 Throttle position sensor board 72-73 only

Porsche 914 Throttle position sensor board 72-73 only

This is a new circut board and a pop rivet to install it. It comes with an instruction sheet. You may notice that your 914 cuts out or hesitates at certian throttle settings (mostly it stumbles when you start to accelerate. One cause can be that...

Porsche 914 Throttle position sensor board 2.0

Porsche 914 Throttle position sensor board 2.0

This is a new circut board and a pop rivet to install it. It comes with an instruction sheet. You may notice that your 914 cuts out or hesitates at certian throttle settings (mostly it stumbles when you start to accelerate. One cause can be that...

Set of 50 Cheese Head screws and washers Zinc plated

Set of 50 Cheese Head screws and washers Zinc plated

This is a set of cheesehead screws with washers for those that want the stock style. They are zinc and prone to stripping. If you want to avoid those issues we highly recomment the sainless allen verstion of this fastner. Available for not much more.

Speednut set of 14 for letters

Speednut set of 14 for letters

This is a complete set of 14 speednuts that can be used to attach the letters to the grill.

Windage Tray Oil Baffle Seal - Set of 4

Windage Tray Oil Baffle Seal - Set of 4

These are all new silicone windage tray seals. Don't forget to replace these when you rebuild your motor.

Wiring cloth tape - for harness 180'

Wiring cloth tape - for harness 180'

If you arere wrapping your wiring harness, this is the stuff you want. 180' roll (best value)

Wiring Tab Cover. Correct gloss fits well per 1'

Wiring Tab Cover. Correct gloss fits well per 1'

Correct wiring harness tab covers.  Soft rubber with correct gloss level and it actually grips and holds well. It takes about 9' for every tab on your car.

914 Rear strut tower caps set of 2

914 Rear strut tower caps set of 2

 This listing is for a set of 2 (enough for one car) rear strut tower caps. If yours are missing or crusty like most now you can replace them with brand new parts. I don't know of anywhere where you can buy these but here.

Fire wall back pad - foil

Fire wall back pad - foil

This is a firewall back pad that is lighter than OEM and you can install with optional velcro to make it easy to remove and reinstal. This way you can clean behind it if you want. 

An exellent replacement for your OEM pad

24" Velcro

24" Velcro

This is 24" of Velcro for the attachement of the firewall back pads or any other items that may need to attached.

The picture shows how I used it to attach the firewall back pad.

 

 

914 Engine deck lid welting enough for all 3 sections

914 Engine deck lid welting enough for all 3 sections

This is the rubber "gasket" seal that isolates the grill from the body and deck lid. Most of these have been pained over or ar in very poor repair. Now you can replace all 3 sections cheap. NLA OEM

914 Engine seal set of all 4

914 Engine seal set of all 4

This is your best value for all 4 seals. These replace the seals that help keep all the hot air from rising into the engine compartment, robbing your engine of horse power. Compare to 914-504-117-10 rear 914-504-155-10 sides and front.

914 Engine Tin Grommet

914 Engine Tin Grommet

NLA from factory. These are for the large openings in the Engine Tin. Sold individually, you will need 2 for a complete car.

914 Oil tower gasket

914 Oil tower gasket

This is a reproduction of the OEM oil tower gasket that will compress over time and leak. The twist with mine is they are slightly thicker than OEM as over time the spring will stretch. This will but a good tension on the gasket and stop it from...

914 Rear Trunk Bulkhead Seal

914 Rear Trunk Bulkhead Seal

This is the seal that keeps water from rolling back into the trunk from the engine compartment. It is critical to keeping your trunk dry. Slightly taller than OEM but creates a much better seal.

914 Wiring harnes snorkel tube

914 Wiring harnes snorkel tube

This is the part you need to seal the tunnel area behind the firewall to the engine tin. I made it long enough that it should fit most 6 applications, but will still work for the 4. Made from durable silicone.

914.424.592.00 Emergency Brake Bellows - Set of 2

914.424.592.00 Emergency Brake Bellows - Set of 2

Set of two Ebrake bellow boots. These are NLA 914.424.592.00.

Engine Deck Lid Seal

Engine Deck Lid Seal

This is the "seal " that you see between the back glass and the deck lid. It hides the gap, and keeps water from rolling directly in the opening.

Porsche 914 Firewall back pad

Porsche 914 Firewall back pad

This is a solution to the OEM back pad that absorbs water and will cause rust on the back firewall. It is precision cut using the OEM as a template. The material is fireresistant and has excellent sound deadning properties. It is soft as it is...

Rubber bumper to keep trunk from hitting deck lid

Rubber bumper to keep trunk from hitting deck lid

This is the NLA rubber "bumper" that keeps the rear trunk lid from hitting the engine deck lid. You will need the metal angle bracket that holds this in place, as it is not included.

914 CV bolt drilled for safety wire includes wave washer

914 CV bolt drilled for safety wire includes wave washer

This is a single new CV bolt machined for safety wire, with wave washer included. 16 required per car.

Stainless wire for CV bolts 36" min

Stainless wire for CV bolts 36" min

This is a 36" coil of stainless steel safety wire. To be used with drilled CV bolts.

Porsche 914 CV joint gasket - 1

Porsche 914 CV joint gasket - 1

This is the gasket you need to replace the OEM one when you clean up the CV jooint or put a new one in.

4 required per car

Schorr washer for CV joint - each

Schorr washer for CV joint - each

Now you can get exactly how many you need without having a lifetime supply of these. Quantity is each.

Try shipping media mail to save on shipping

Schnorr washers for CV joint bolts - individual part

Schnorr washers for CV joint bolts - individual part

Don't want to order a massive quantity of these to sit on your shelf forever. Now you can order only what you want.

Use our first class mail option to save shipping cost as these are small.

Engine deck lid base for pull 914.512.177.10

Engine deck lid base for pull 914.512.177.10

This is the machined base for the engine deck lid pull. It holds the back pad to the fireall in this area also.

pull for deck lid machined delrin

pull for deck lid machined delrin

This is the engine deck lid pull only. If your base is good and you only need the knob, this is what you need.

914 Rear deck lid relaease cable

914 Rear deck lid relaease cable

This is a direct replacement for the rear deck cable cable, it has a threadded termination that will screw right into the handle base to allow you to pull. This typically fails at the latch portion where the stress is at the termination there. I...