Engine parts

 

021256325A 021256326A Heater blower plate gasket kit

021256325A 021256326A Heater blower plate gasket kit

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256325A Heater blower plate gasket (Right)

021256325A Heater blower plate gasket (Right)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256326A Heater blower plate gasket (Left)

021256326A Heater blower plate gasket (Left)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

1.8 intake Plenum tube both larger holes 022.129.967T

1.8 intake Plenum tube both larger holes  022.129.967T

This is the 1.8 intake elbow that has 2 larger holes.

The 022.129.967 is the one you will want if you need 2 different size holes. 

1.8 intake Plenum tube holes different sizes 022.129.967

1.8 intake Plenum tube holes different sizes  022.129.967

This is the 1.8 intake elbow that has 2 diferent size holes.

The 022.129.967T is the one you will want if you need 2 larger holes. 

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

This is a reproduction of early rain tray. These are more sturdy than the OEM ones as the material has a higher melting point and is thicker. Don't forget the rubber bumper that keeps the rear trunk lid from hitting this. I have them reproduced...

Alternator Inspection Cover

Alternator Inspection Cover

Plastic cover for the fan housing to allow access to the alternator top bolt. For adjustment with engine installed. Helps keep airflow directed for cooling.

Alternator wiring harness 70-76 4 cylinder only plug and play

Alternator wiring harness 70-76 4 cylinder only plug and play

This is a direct replacement fro your old worn out wirring harness. If you replace your alternator you more than likely will need the rubber, now you can eliminate any potential problems by simply replacing. Correct gage wires used along with new...

(1)

Bearing Shell

Bearing Shell

These are the Cooling Flap control bar bushings that seat in the Fan Shroud. 2 required per car. Fits all Porsche 914 engines as well as: 911 1974-77 912 1968, 69 & 76 VW Type IV 1968-74 VW Bus 1972-83 021-119-187, 021 119 187, 021.119.187, 021119187

Cary's suspension gussets for control arm area.

Cary's suspension gussets for control arm area.

These are the blanks for gussets you would use to reinforce the suspension control arms. Made to Cary's specification these are what he uses to reinforce this area. Made under license form Middlemotor LLC. This is a set for one side only. If you intend to do both you will need to buy 2 sets.

Cover cap for adjuster cover on ECU box

Cover cap for adjuster cover on ECU box

I didn't even know mine was missing until I checked. These are not being shown as available alone, so no suprice when they got lost or damaged they were never replaced. These are so inexpensive you almost can't afford not to. Yes the last picture...

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

This is a reproduction cylinder head temperature sensor that is construcetd from stainles steel. Utilizing tested internal componets that have been used to replace these (Original Customs was originally remanufacturing these). Now you can replace...

Fuel filter only

Fuel filter only

This includes - The fuel filter This is the late front mounted fuel filter Note the picture with the fuel pump is for illustration only. The second picture is what is in the "kit" Please note ethanol will deterrorate the hoses pretty quickly with...

Porsche 914 clutch cable 914.423.401.05

Porsche 914 clutch cable 914.423.401.05

Clutch cable for 914 -4

Picture shows all of the other parts you may want, but this is for a clutch cable only.

Set of 50 Cheese Head screws and washers Zinc plated

Set of 50 Cheese Head screws and washers Zinc plated

This is a set of cheesehead screws with washers for those that want the stock style. They are zinc and prone to stripping. If you want to avoid those issues we highly recomment the sainless allen verstion of this fastner. Available for not much more.

Side shift 914 and 911 knuckle bushings set 911 424 223 03

Side shift 914 and 911 knuckle bushings set 911 424 223 03

These are the bushings for the late coupler on the side shift linkage. These are toleranced correctly so they fit snug and are easier to install. Looks like these are part # 911.424.223.03. I had ordered new from factory and they were sloppy....

Wiring cloth tape - for harness 70 or 180'

Wiring cloth tape - for harness 70 or 180'

If you are re wrapping your wiring harbness, this is the stuff you want. 70ft roll, or 180' roll (best value)