Engine

 

021256325A 021256326A Heater blower plate gasket kit

021256325A 021256326A Heater blower plate gasket kit

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256325A Heater blower plate gasket (Right)

021256325A Heater blower plate gasket (Right)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256326A Heater blower plate gasket (Left)

021256326A Heater blower plate gasket (Left)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

1.7 intake hose 022 129 967 With lip for oil bath or without

1.7 intake hose 022 129 967 With lip for oil bath or without

This is the 1.7 intake taht is set up to re sue the metal hardware for the oil bath set up. or to utilize a clamp for the non oil bath air filter. If you are in doubt you can select the oil bath and it can be trimmed off. I was asked to make...

1.8 intake Plenum tube both larger holes 022.129.967T

1.8 intake Plenum tube both larger holes  022.129.967T

This is the 1.8 intake elbow that has 2 larger holes.

The 022.129.967 is the one you will want if you need 2 different size holes. 

1.8 intake Plenum tube holes different sizes 022.129.967

1.8 intake Plenum tube holes different sizes  022.129.967

This is the 1.8 intake elbow that has 2 diferent size holes.

The 022.129.967T is the one you will want if you need 2 larger holes. 

Throttle body gasket for 1.7 intake

Throttle body gasket for 1.7 intake

This is a NLA gasket available only here only $10.50

1.8 Throttle body seal for intake

1.8 Throttle body seal for intake

This is the throttle body gasket for the 1.8 intake. I've made the 1.7 for years and finally the 1.8 as a number of you have been asking for these, as NOS is hard to find.

porsche 914 2.0 Throttle body gasket

porsche 914 2.0 Throttle body gasket

This is a reproduction 2.0 Throttle body gasket. OEM is no longer available.

2.0L Throttle Body to Plenum Seal

2.0L Throttle Body to Plenum Seal

NLA from factory, this is the 2.0L Throttle Body to Plenum Rubber Sleeve. Molded with the hose clamp stop in it just like OEM.

914 Engine seal set of all 4

914 Engine seal set of all 4

This is your best value for all 4 seals. These replace the seals that help keep all the hot air from rising into the engine compartment, robbing your engine of horse power. Compare to 914-504-117-10 rear 914-504-155-10 sides and front.

914 Engine Tin Grommet

914 Engine Tin Grommet

NLA from factory. These are for the large openings in the Engine Tin. Sold individually, you will need 2 for a complete car.

914 High temp Heater hose

914 High temp Heater hose

This is a set of high temp silicone heater hoses that attach from the heater box to the body. These list at $56 at other sites $32 For a set here

914 Oil tower gasket

914 Oil tower gasket

This is a reproduction of the OEM oil tower gasket that will compress over time and leak. The twist with mine is they are slightly thicker than OEM as over time the spring will stretch. This will but a good tension on the gasket and stop it from...

914 Valve Cover Gaskets - Set of 2

914 Valve Cover Gaskets - Set of 2

This is an improved version the OEM part. Over time the bales on the valve covers loose tension. These are made from a similar material that is slightly thicker and denser to create a good tight seal.

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

914.424.075.03 914 heater cable for 75-76

914.424.075.03 914 heater cable for 75-76

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

914/6 dipstick for fender oil cooler

914/6 dipstick for fender oil cooler

Thsi is a replica of the factory 914/6 dipstick for the offset oils cooler in the fenderwell. They are not identical to factory close. We hand made each of these. Will start shipping 7/14/14 More pictues will be added as soon as they are back from finishing.

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Cooling flap bushings for use on 911, and type 4 engines

Branch Piece Air Distributor

Branch Piece Air Distributor

High quality reproduction of the stacked elbow for the air cleaner. Includes correct size brass fittings for easy assembly.

Early side shift firewall to housing gasket

Early side shift firewall to housing gasket

This is the tail shift gasket that holds the plastic housing to the firewall. This is only the "band" at the firewall.

 914.424.502.00

Engine bay blower hose long (1)

This is a single blower hose long enough to reach the passenger side air inlet. An excellent low temp option. Better than the Paper and aluminum OEM ones

Engine parts package

Engine parts package

Engine kit -Set of all 4 engine seals, the heater grommets in sheet metal, set of 50 stainless engine tin allen head screws with washers, 2 alternator harness grommets, 2 heater cable nipples, and set of heater hoses 

Engine screw kit Stainless w/washer allen head

Engine screw kit Stainless w/washer allen head

This is a set of 50 allen head screws with washers that replace the original "cheesehead" screws. They are stainless with stainless washers. $20

Oil cooler and tin gasket 021119329

Oil cooler and tin gasket 021119329

Another NLA part we all need. This gasket goes on the engine tin and seals the gap between the cooler and the tin.  Made from silicone to offer a better seal. It also acts as a buffer between the two.

Now available at a reasonable price.

Porsche 914 heater cable nipple Set

Porsche 914 heater cable nipple Set

This listing is for a set of 2 heater cable covers or "nipples" that keep water from getting into the center tunnel from the firewall side. Most of these have baked out as they were made from organic rubber. I have made these from a higher temp...

PCG42407501 914 heater cable for 914/6

PCG42407501 914 heater cable for 914/6

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

Throttle Position Sensor Board Early 1.7 ONLY: 1970-1971

Throttle Position Sensor Board Early 1.7 ONLY: 1970-1971

This is the throttle position sensor board for the early 1.7 TPS. It will only work on the early (70-71) TPS, as they are quite diferent from the late.

Porsche 914 Throttle position sensor board 72-73 only

Porsche 914 Throttle position sensor board 72-73 only

This is a new circut board and a pop rivet to install it. It comes with an instruction sheet. You may notice that your 914 cuts out or hesitates at certian throttle settings (mostly it stumbles when you start to accelerate. One cause can be that...

Porsche 914 Throttle position sensor board 2.0

Porsche 914 Throttle position sensor board 2.0

This is a new circut board and a pop rivet to install it. It comes with an instruction sheet. You may notice that your 914 cuts out or hesitates at certian throttle settings (mostly it stumbles when you start to accelerate. One cause can be that...

Windage Tray Oil Baffle Seal - Set of 4

Windage Tray Oil Baffle Seal - Set of 4

These are all new silicone windage tray seals. Don't forget to replace these when you rebuild your motor.

Porsche 914 Firewall back pad

Porsche 914 Firewall back pad

This is a solution to the OEM back pad that absorbs water and will cause rust on the back firewall. It is precision cut using the OEM as a template. The material is fireresistant and has excellent sound deadning properties. It is soft as it is...

Fire wall back pad - foil

Fire wall back pad - foil

This is a firewall back pad that is lighter than OEM and you can install with optional velcro to make it easy to remove and reinstal. This way you can clean behind it if you want. 

An exellent replacement for your OEM pad

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

This is a reproduction cylinder head temperature sensor that is construcetd from stainles steel. Utilizing tested internal componets that have been used to replace these (Original Customs was originally remanufacturing these). Now you can replace...

Cover cap for adjuster cover on ECU box

Cover cap for adjuster cover on ECU box

I didn't even know mine was missing until I checked. These are not being shown as available alone, so no suprice when they got lost or damaged they were never replaced. These are so inexpensive you almost can't afford not to. Yes the last picture...

Rain Hats for carbs

Rain Hats for carbs

These will not have any holes in them, you will need to drill them. These are made to fit Weber Idf's, Ida's, or any Weber using the 7''x 4.5" oval air cleaner. Also fits Dellorto DRLA's, Solex P40II. This is a set of rain hats that fit any...

Late Rain tray 91451218910

Late Rain tray 91451218910

This is our reproduction of the rain trays that keep your engine compartment from getting wet. They superceeded the early version (which we also make), and look identical to factory. We did however make them slightly thicker and out of a better...

Engine bay rain tube funnel Grommets set of 2 914.572.913.10

Engine bay rain tube funnel Grommets set of 2 914.572.913.10

These are the funnel tube grommets that hold the tube in place on the sheetmetal. These are made from silicone so that they should hold up a little better that the OEM version. These NLA pieces will dress up your engine shelf nicely, why reuse your crusty old rubber ones if you don't have to?

Rain tray drain tubes set of 2 PCG 571 900 00

Rain tray drain tubes set of 2 PCG 571 900 00

This is a set of drain tubes that are needed to allow the water to drain from the rain tray through the engine compartment. The funnels and grommets are not included with these. It is not 100% correct for the OEM hose, butismuch c,oser than the...