GB Specials

 

021256325A 021256326A Heater blower plate gasket kit

021256325A 021256326A Heater blower plate gasket kit

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256325A Heater blower plate gasket (Right)

021256325A Heater blower plate gasket (Right)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256326A Heater blower plate gasket (Left)

021256326A Heater blower plate gasket (Left)

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

1.7 intake hose 022 129 967 With lip for oil bath or without

1.7 intake hose 022 129 967 With lip for oil bath or without

This is the 1.7 intake taht is set up to re sue the metal hardware for the oil bath set up. or to utilize a clamp for the non oil bath air filter. If you are in doubt you can select the oil bath and it can be trimmed off. I was asked to make...

1.8 intake Plenum tube both larger holes 022.129.967T

1.8 intake Plenum tube both larger holes  022.129.967T

This is the 1.8 intake elbow that has 2 larger holes.

The 022.129.967 is the one you will want if you need 2 different size holes. 

1.8 intake Plenum tube holes different sizes 022.129.967

1.8 intake Plenum tube holes different sizes  022.129.967

This is the 1.8 intake elbow that has 2 diferent size holes.

The 022.129.967T is the one you will want if you need 2 larger holes. 

914 CV bolt drilled for safety wire includes wave washer

914 CV bolt drilled for safety wire includes wave washer

This is a single new CV bolt machined for safety wire, with wave washer included. 16 required per car.

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

914 Early rain tray pre 74 more sturdy than stock 914.512.189.10

This is a reproduction of early rain tray. These are more sturdy than the OEM ones as the material has a higher melting point and is thicker. Don't forget the rubber bumper that keeps the rear trunk lid from hitting this. I have them reproduced...

914 Engine Tin Grommet

914 Engine Tin Grommet

NLA from factory. These are for the large openings in the Engine Tin. Sold individually, you will need 2 for a complete car.

914 Flat tow Bar

914 Flat tow Bar

This is a flat tow bar that I use to tow to all the events over 3 hours. My significant other isn’t really into all day drives, that and I like the insurance that if it should decide to stop running at any point I can easily hook up and get...

914 Floor mats -Early and Late style -MADE TO ORDER

914 Floor mats -Early and Late style -MADE TO ORDER

We finally decided to look at making a floormat for our beloved 914. One that fits properly both early and late. Heads up - These are being made to order so the leat time is about 10 days We may stock more popular configureation as time goes on...

914 Heater blower hose set (dual) Low temp option

914 Heater blower hose set (dual) Low temp option

These are a better option than the factory paper and aluminum hoses in that they have an internal rib that is more durable and helpsthem to not be crushed easily. An excellent value compared to the full rubber option.

Set of 2 fro dual blower.

914 MM master Cylinder NOT URO 911.305.012.00

914 MM master Cylinder NOT URO 911.305.012.00

Finally we have recreated the 19mm master cylinder that you have no option but to but in inferror parts or pay the ATE price. Providing you with a reasonalble solution, and improvements to make installation easier. Each assembly has been QC'd...

914.424.224.03 late side shifter Firewall bushing

914.424.224.03 late side shifter Firewall bushing

This is the firewall bushing that will take some of the slop out of your shifting. Normally these are difficult to install, but we have made some changes that will allow for easy installation. We I decided to make these just like the small...

A-Arm Bushing Set

A-Arm Bushing Set

Set of 4 A-Arm Bushings with option for installation Tool.

Alternator Inspection Cover

Alternator Inspection Cover

Plastic cover for the fan housing to allow access to the alternator top bolt. For adjustment with engine installed. Helps keep airflow directed for cooling.

Back pad NEW PLASTIC replacements

Back pad NEW PLASTIC replacements

These replace your OEM paper pressborad ones and are not affected by water or mositure like the OEM ones.

Battery block positive terminal - optional hardware and stud

Battery block positive terminal - optional hardware and stud

This is the NLA battery block that is used on the positive terminal. It's NLA but you can get one here inexpensively. The current configuration allows for the option to add the stud and hardware if you do not have them.They do not come with unless you use the option to add them.

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Bearing Shell - cooling flap bushings set of 2 (1 car) 021119187

Cooling flap bushings for use on 911, and type 4 engines

Brake light / Trans reverse light switch cover 914.613.491.00

Brake light / Trans reverse light switch cover 914.613.491.00

This is the same boot for both application. Fits all years. These are currently availabe at over $20 each. Mine have the correct retaining grove at the base to make a good seal. Save yourself a bunch of cash and get a well made part. These are in...

Caps for Ski Rack mounting holes (set of 6)

Caps for Ski Rack mounting holes (set of 6)

Caps to cover the mounting holes for factory ski racks

Cary's suspension gussets for Trailing Arm Area.

Cary's suspension gussets for Trailing Arm Area.

These are the blanks for gussets you would use to reinforce the suspension trailing arm mounts arms. Made to Cary and "Super-In-Law's" specifications, these are what they useto reinforce this area. Made under license form Middlemotor LLC. This is...

Climate control knobs set of 3 - 1 red 2 black 901.571.917.00

Climate control knobs set of 3 - 1 red 2 black 901.571.917.00

Now you can buy these never available alone parts to spruce up your climate control quickly and inexpensively. This is a set of 3. One Red Two Black They were used on 911, 912, 914, and 930 models from 1965 to 1985.

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

This is a reproduction cylinder head temperature sensor that is construcetd from stainles steel. Utilizing tested internal componets that have been used to replace these (Original Customs was originally remanufacturing these). Now you can replace...

Engine bay blower hose long (1)

This is a single blower hose long enough to reach the passenger side air inlet. An excellent low temp option. Better than the Paper and aluminum OEM ones

Front suspension droplink set with hardware set of 4 (1car)

Front suspension droplink set with hardware set of 4 (1car)

This is a set of 4 drop link bushings manufactured in sections that are contoured to fit the OEM drop links. Each drop link requires 2 sets. Also included is the center bushing and the hardware required to replace the entire assembly. Referr to...

Fuel line grommet 10mm

Fuel line grommet 10mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

H4 Glass Housings for LED or reg bulbs

H4 Glass Housings for LED or reg bulbs

This is an H4 housing that can accomidate our LED bulk kit as well as incadecent bulbs. It is good quality and fitment is good.

Select option for 2 to buy at discounted price.

Hoses from blower to mixing box.914.571.123.10 set of 2

Hoses from blower to mixing box.914.571.123.10 set of 2

These are the hoses that are in the front trunk that go from the mixing box to the lower vent. OEM Part number 914.571.123.10 Not the flimsy paper and aluminum hoses others sell. 

Late Rain tray 91451218910

Late Rain tray 91451218910

This is our reproduction of the rain trays that keep your engine compartment from getting wet. They superceeded the early version (which we also make), and look identical to factory. We did however make them slightly thicker and out of a better...

Late Side Shift Bushing Kit

Late Side Shift Bushing Kit

Get everything you need to eliminate sloppy shifting in one kit, with the option to add the shift housing cover for only $12 more. Kit consists of: 911.424.139.00 911.424.223.03 (x2), 911.424.224.02, 911.424.224.03, and 914 424 239 02.

LED Headlight bulbs

LED Headlight bulbs

These are a set (one car) of LEDs that are rated higher than many others on the market. They have a high and low beam rated at 3900Lumens and 6000 lumens respectively. We have searched many vendors and have located one that we are happy with...

Mirror glass early and late - Glass only

Mirror glass early and late - Glass only

This is the mirror replacement only for the side mirrors that screw on with 2 screws. There is a difference on the mirrors There is an early 70-71 and a late, 72-76. We currently have the late in hand and the early should be ready about 10.5.17....

New Fog light Grills set left and right - like OEM +install kit

New Fog light Grills set left and right - like OEM +install kit

These are the 3rd generation of our fog light grills and we jhave finally got them nailed. Comparable to OEM in material, fit and finish. Utilizing a more durable plastic these will withstand 2x the inpact of the previous generation. They also...

(1)

Oil cooler and tin gasket 021119329

Oil cooler and tin gasket 021119329

Another NLA part we all need. This gasket goes on the engine tin and seals the gap between the cooler and the tin.  Made from silicone to offer a better seal. It also acts as a buffer between the two.

Now available at a reasonable price.

Seat adjuster rebuild kit for one car and special tool included

Seat adjuster rebuild kit for one car and special tool included

This kit is enough to do 2 seats or one car. It includes 2 of each bushing 2 drive pins and the special tool you will want.

Solid Trailing Arm With Bushing Set

Solid Trailing Arm With Bushing Set

New solid trailing Arm Set with 4 polygraphite bushings.

Special tool for drive pins - seat adjuster applicatiom SPT900

Special tool for drive pins - seat adjuster applicatiom SPT900

This is a special tool to install drive pins. It allows you to center the pin and use a hammer to wedge the pin in.

Turn Signal Lens Set Group Buy

Turn Signal Lens Set Group Buy

Now until 4/20/2017, add a set of lens seals to your order and use coupon code GBLENS2017 to receive free first class mail shipping.

Upper Front Strut Tower Rubber Bushing Set

Upper Front Strut Tower Rubber Bushing Set

These are a set of 2 (enough for one car), upper strut tower bushings. These are those pesky rubber bushings that go inside the top of the strut tower mount. Yes you can buy new metal mounts with the new rubber.....at $180 each! I designed these...

Vent hose bushing 823823591 999.702.049.50 set of 2

Vent hose bushing 823823591  999.702.049.50 set of 2

Long extinct grommet in the firewal for the vent line into the charcoal canaster.

Also known as 823823591 999.702049.50

 

SET OF 2 

Wiring cloth tape - for harness 180'

Wiring cloth tape - for harness 180'

If you arere wrapping your wiring harness, this is the stuff you want. 180' roll (best value)

Wiring Tab Cover. Correct gloss fits well per 1'

Wiring Tab Cover. Correct gloss fits well per 1'

Correct wiring harness tab covers.  Soft rubber with correct gloss level and it actually grips and holds well. It takes about 9' for every tab on your car.

Fuel line grommet 8mm

Fuel line grommet 8mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

911.424.139.00 Ball cup for shifter at transmission

911.424.139.00 Ball cup for shifter at transmission

This is the ball cup that fits into the lever on the transmission that connects to the rod. Don't forget to check out the other related items as you may need them.

914 Trunk lock gasket

914 Trunk lock gasket

These are a reproduction of the OEM version, only they actually seal. OEM was a plastic that didn't actually seal. Mine is a soft silicone that seals and will actually help heep water out of your trunk. At this price, you really can't not replace it.

Seat adjuster outer guide bushing 914 521 205 10

Seat adjuster outer guide bushing 914 521 205 10

This is the outer guide bushing for the seat adjuster rod. It helps to transfer torque on the bar to help release the tilt. Note that I do sell a complete kit with 2 bushingsm the smaller guide bushings, new roll pins. Best of all it comes with a...

Seat adjuster bushing 914 521 203 10

Seat adjuster bushing 914 521 203 10

This is the long discontinued seat adjuster bushing that allows the armature to rotate at the spring. This is for one bushing. Note that I do sell a complete kit with 2 bushings, the 2 other main guide bushings, new roll pins. Best of all it...

Early E-Brake spring 901.424.543.00

Early E-Brake spring 901.424.543.00

This spring is notorious for breaking and in careful evaluation we realized that the way the OEM part was made concentrated force right where they were breaking. We have made a design imprevement that will make these last longer than the OEM...

911 914 Insturnment mounting ring 911.641.301.00 115mm

911 914 Insturnment mounting ring 911.641.301.00 115mm

This is a single insturnment mounting ring for you 914 or 911. 911 applications require 2 if you are replacing both. 914 only requires 1. I have made these from silicone s oyou can easly replace without having to remove the wires or cables from...

911 914 Insturnment mounting ring 911.641.902.00 100mm

911 914 Insturnment mounting ring 911.641.902.00 100mm

This is a single insturnment mounting ring for you 914 or 911. Both applications require 2 if you are replacing both. I have made these from silicone s oyou can easly replace without having to remove the wires or cables from the insturnments....

911.641.901.00 Insturnment rubber grip ring - clock 80mm 1pc

911.641.901.00 Insturnment rubber grip ring - clock 80mm  1pc

This is the 80mm clock retainer rubber also used in the small combo gauge on the opposite side All of the seals are shown so that you can see the scale is correct. You would normally need to order 2 for one car. 

Headlight adjuster backing set of 4 (enough for one car)

Headlight adjuster backing set of 4 (enough for one car)

These are the NLA headlight adjuster backs, this is enough to replace all on one car.

Rain tray drain tubes set of 2 PCG 571 900 00

Rain tray drain tubes set of 2 PCG 571 900 00

This is a set of drain tubes that are needed to allow the water to drain from the rain tray through the engine compartment. The funnels and grommets are not included with these. It is not 100% correct for the OEM hose, butismuch c,oser than the...

914 Targa Top Latch Cups Set 914.559.227.10

914 Targa Top Latch Cups Set 914.559.227.10

This is a set of the targa latch cups that are in the trunk area. They are factory correct and yes made my me. These are not a cheap URO part. You can even by for less from me!

Airbox drain tubes set of 3 PCG 571 900 00

Airbox drain tubes set of 3 PCG 571 900 00

These are the air box drain tubes NOT sourced at your local hardware store. They are actually ribbed and make a very firm attachment onto the fittings. The T fitting is shown on the assembly, however, it is NOT included.

914.722.021.10 Jack strap with hardward (stainless) set of 2

914.722.021.10 Jack strap with hardward (stainless) set of 2

Finally a high quality rubber part with hardware made to look like OEM, except it's stainless and will not rust like OEM!

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

This is our new reproduction front trunk seal with the OEM profile. It has softer corners to help the trunk to seat better than OEM. SHOWN WITH OPTIONAL BULKHEAD SEAL

(1)