Misc Seals

021256325A 021256326A Heater blower plate gasket kit

021256325A 021256326A Heater blower plate gasket kit

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256325A Heater blower plate gasket

021256325A Heater blower plate gasket

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

021256326A Heater blower plate gasket

021256326A Heater blower plate gasket

Constructed from high temp silicone this should last for many years and compress into the edges to provide a better seal. The OEM was a felt / fiber material that I suspect may have contained asbestos. I did find some factory seals to make a...

1.8 Throttle body seal for intake

1.8 Throttle body seal for intake

This is the throttle body gasket for the 1.8 intake. I've made the 1.7 for years and finally the 1.8 as a number of you have been asking for these, as NOS is hard to find.

2.0L Throttle Body to Plenum Seal

2.0L Throttle Body to Plenum Seal

NLA from factory, this is the 2.0L Throttle Body to Plenum Rubber Sleeve. Molded with the hose clamp stop in it just like OEM.

45 Degree Rubber Sleeve for Fuel Line

45 Degree Rubber Sleeve for Fuel Line

This grommet goes in the engine compartment tin where the fuel line passes through the the tin.

6 piece floor vinyl kit NEW

6 piece floor vinyl kit NEW

This is the perfect compliment to a new carpet kit. One of the things that doesn't quite make sense is installing a new carpet kit and leaving the crusty old vinyl on the floor. This is a pretty basic kit, it does require that you cut the seat...

901-628-923-01 Wiper Grommet Female - Set of 2

901-628-923-01 Wiper Grommet Female - Set of 2

This is a gasket that has been way overpriced for too long. Help me make these and other more afordable parts with your purchase today!

 

part number 901.628.923.01

901.628.926.00 Wiper cap

901.628.926.00 Wiper cap

While you are replacing your wiper grommets might as well replace these. Most are in poor shape 

901.741.291.00 Side shift sealing sleeve #50 on the PET

901.741.291.00 Side shift sealing sleeve #50 on the PET

This is the rear sealling bellows for the early side shift transmission. PET catalog shows part as 901.741.291.00. Interestingly enough others reference this as Speedometer Cable Boot Fits 911, 1965-1971. This was reproduced off a stock 914 part...

911 914 Insturnment mounting ring 911.641.301.00 115mm

911 914 Insturnment mounting ring 911.641.301.00 115mm

This is a single insturnment mounting ring for you 914 or 911. 911 applications require 2 if you are replacing both. 914 only requires 1. I have made these from silicone s oyou can easly replace without having to remove the wires or cables from...

911 914 Insturnment mounting ring 911.641.902.00 100mm

911 914 Insturnment mounting ring 911.641.902.00 100mm

This is a single insturnment mounting ring for you 914 or 911. Both applications require 2 if you are replacing both. I have made these from silicone s oyou can easly replace without having to remove the wires or cables from the insturnments....

911.641.901.00 Insturnment rubber grip ring - clock 80mm 1pc

911.641.901.00 Insturnment rubber grip ring - clock 80mm  1pc

This is the 80mm clock retainer rubber also used in the small combo guage on the opposite side All of the seals are shown so that you can see the scale is corrrect. You would normally need to order 2 for one car. Also check out the speedometer drivre cable bushing I have inexpensively 911.641.520.00

914 Alternator harness grommet

914 Alternator harness grommet

These are the grommets that go on the wirring harness at the tin behind the alternator, and at the sheetmetal on the engine. This is for one grommet.

914 Door handle gaskets

914 Door handle gaskets

These are the 4 pieces of rubber that isolate the handle formr the painted body. 2 for each side, This will do one car.

914 Door handle gaskets

914 Door handle gaskets

These are the 4 pieces of rubber that isolate the handle formr the painted body. 2 for each side, This will do one car.

914 Door Light Rubber Gasket - Set of 2

914 Door Light Rubber Gasket - Set of 2

Gasket for the door position sensor that operates the interior dome light.

914 Early door end caps

914 Early door end caps

These are reproductions of the no longer available early door end caps, These have been reproducted in rubber for an easier fit. $32

914 Early gas cap seal

914 Early gas cap seal

A simple solution for replacement of your early cap seal. Made from solvent resistant rubber. An inexpensive fix for the gas smell if you cap leaks.

Early cap only

914 Engine deck lid welting enough for all 3 sections

914 Engine deck lid welting enough for all 3 sections

This is the rubber "gasket" seal that isolates the grill from the body and deck lid. Most of these have been pained over or ar in very poor repair. Now you can replace all 3 sections cheap. NLA OEM

914 Engine Tin Grommet

914 Engine Tin Grommet

NLA from factory. These are for the large openings in the Engine Tin. Sold individually, you will need 2 for a complete car.

914 Expansion Tank Gasket

914 Expansion Tank Gasket

This fits between the expansion tank and the gas tank.

914 Eyebrow grommets set of 6

914 Eyebrow grommets set of 6

This is a set of all 6 grommets you will need to install the eye lid metal at the base of the headlight bucket. I made these slightly easier to install.

914 Fender to cowl seals

914 Fender to cowl seals

These are the 2 short seals that close the gap between the fender and the cowl edge. Sold as a set of 2.

914 Fog light gaskets set of 2 (enough for one car)

914 Fog light gaskets set of 2 (enough for one car)

This is a fog light gasket that replaces the crusty OEM ones you've probably had in since the car was new. $15 a set.

Not the lens portectors can be bought with for an additional savings! Shown but not included unless you select the option.

914 Foil and velcro for back pad

This is the the foil (enough to do all the edges ) and the velcro you can use to attach the engine firewall back pad.

914 Fresh air box top seal (SEAL ONLY)- Late for use with grill

914 Fresh air box top seal (SEAL ONLY)- Late for use with  grill

This is the seal that goes on the top of the airbox that holds the grill in place. The early cars do not have the grills but you can add one by changing out this seal and including a new plastic grill.

 

914 Front trunk Bulkhead seal

Same as set only excludes main seal

This is the upper "bulkhead seal" infront of the gas tank that runs from strut to strut. Available without buying the entire set. $18 compare to OEM at $50, only mine has an aluminum clip and is slightly taller for a better seal.

914 Front trunk plugs set of 9

914 Front trunk plugs set of 9

This is a full set all 9 of the front trunk plugs. For the holes that were in the cars til late 75. They are made from silicone and make a good seal.

914 Front trunk seal set to new OEM profile

914 Front trunk seal set to new OEM profile

This is a set of the main front trunk seal and the upper bulkhead seal. It is not like OEM only the corneres are actually molded into the complete seal. This makes them permanently bonded and will not seporate like the OEM does. It is NOT a...

(1)

914 High Temp Silicone Valve Cover Gaskets (set of 2)

914 High Temp Silicone Valve Cover Gaskets (set of 2)

These are a set of high temp silicone gaskets from that are slightly oversized that will compress to a perfect fit. These are reusable. This is a set of 2 perfect for your next oil change.

914 injector covers (set of 4) 311906102

914 injector covers (set of 4)  311906102

Injector covers to replace your torn or worn out covers. Your wiring will thank you.

914 Inner door fuzzeys set of 2

914 Inner door fuzzeys set of 2

These are the ones that go on the inside track and can be replaced without any dissasembly of the door. (set of 2)$38.

914 Jack strap -Rubber only set of 2

914 Jack strap -Rubber only set of 2

These are the new formulation more flexable jack strap rubber. While the straps do not display the pat number on them are are equivalent to the OEM parts. This listing is for a set of 2 pieces as shown.

914 Late door end cap set left and right

914 Late door end cap set left and right

These are reproductions of the OEM no longer available from factory. This is a set left and right. Compare to part # Left -914.542.173.10 Right-914.542.173.10

914 late gas cap seal

914 late gas cap seal

Mine was missing and I wondered why I could smell gas when I cornered. Fits late gas caps

914 late side shifter bellows

914 late side shifter bellows

Yes 2 are shown, but you only need one. This is the bellows that goes at the rear of the shift linkage and keeps crud from getting into the shifter housing (the black plastic cup).

They were NLA, but you can get them here.

914 Main Targa Seal Reproduction

Upper main seal. Note the gap below the seal, the lower targa seal goes there.

This seal is just like like the OEM and has molded rubber corner blocks that connect to the side seals. The sides are molded to fit the corner bend at the top of the windshield (like OEM), and are bonded together. Fits all years.

914 Mirror Base Gasket

914 Mirror Base Gasket

Mirror base gasket. This is one piece, goes between the mirror and the door.

914 Oil tower gasket

914 Oil tower gasket

This is a reproduction of the OEM oil tower gasket that will compress over time and leak. The twist with mine is they are slightly thicker than OEM as over time the spring will stretch. This will but a good tension on the gasket and stop it from...

914 Outer door fuzzeys set of 2

914 Outer door fuzzeys set of 2

These are the metal strips with the outer Fuzzey that secure into the aluminum track on the outside edge of the door. set of 2. $29

914 Outer Window Scraper Seal Set

914 Outer Window Scraper Seal Set

These are the "scraper" seals that fit in the window tracks on the outside. It "scrapes" the window as it rolls down and up. Sold as a set.

914 Rear strut tower caps set of 2

914 Rear strut tower caps set of 2

 This listing is for a set of 2 (enough for one car) rear strut tower caps. If yours are missing or crusty like most now you can replace them with brand new parts. I don't know of anywhere where you can buy these but here.

914 rear sway bar bushing set of 2 90133379304

914 rear sway bar bushing set of 2 90133379304

These are the new thermally enhanced rear sway bar bushings, I include both, think about it, do you really only want to replace one? These have been NLA for quite some time and I have been hand casting these. The quality is vastly improved. The...

914 rear tail light lens seal

914 rear tail light lens seal

This is a set of soft silicone cords that are used to seal the lens to the housing. These ARE NOT the seal between the body and housing.

914 Rear Targa Seal with Fuzzy Strip - OEM Profile

914 Rear Targa Seal with Fuzzy Strip - OEM Profile

This is my new and improved version of the rear targa seal. It has the OEM profile and even the fuzzy on the contact edge to prevent squeaking. This part is held in place with the OEM metal strips. 

914 Rear Trunk Bulkhead Seal

914 Rear Trunk Bulkhead Seal

This is the seal that keeps water from rolling back into the trunk from the engine compartment. It is critical to keeping your trunk dry. Slightly taller than OEM but creates a much better seal.

914 Side marker electrical boot 914.631.218.10 set of 2

914 Side marker electrical boot 914.631.218.10 set of 2

Now you can get a set of 2 quality reproduction side marker lens caps. These seal the crud out and help to minimize corrosion of the contacts. As these see all the elements they are a critical seal. Now you can replace your brittle or missing...

914 Side marker lens seal kit (set of 2)

914 Side marker lens seal kit (set of 2)

These have been improved over the original design. They are constructed from soft neoprene, and have been designed to actually fit the lens correctly. Note the undercut relief for the inner edge of the seal. You will not find a better seal. These fit like OEM, only better.

914 Tail Light Gasket Set

914 Tail Light Gasket Set

These are the gaskets that go between the body and the tail light assembly. This is a set of 2. Only $24

914 Targa Top Latch Cups Set 914.559.227.10

914 Targa Top Latch Cups Set 914.559.227.10

This is a set of the targa latch cups that are in the trunk area. They are factory correct and yes made my me. These are not a cheap URO part. You can even by for less from me!

914 Transmission tail cone gasket

914 Transmission tail cone gasket

This is the gasket you need to remove the tail cone and reinstall. If you don't want to pay for an entire kit you can get just the one you need.

914 Triangle Window Seal - Set of 2

914 Triangle Window Seal - Set of 2

Slightly larger than OEM to fill the gap between the vertical bar and the door panel, with a more refined edge for a cleaner install.

914 Trunk lock gasket

914 Trunk lock gasket

These are a reproduction of the OEM version, only they actually seal. OEM was a plastic that didn't actually seal. Mine is a soft silicone that seals and will actually help heep water out of your trunk. At this price, you really can't not replace it.

914 Valve Cover Gaskets - Set of 2

914 Valve Cover Gaskets - Set of 2

This is an improved version the OEM part. Over time the bales on the valve covers loose tension. These are made from a similar material that is slightly thicker and denser to create a good tight seal.

914 Vibration dampening bushing A434-16 91433351301

914 Vibration dampening bushing A434-16 91433351301

This is a reproduction of the NLA vibration dampening bushing for the rear strut tower. Compare to 914 333 513 01. I am making another style also (click on detail for more info) $40 a set

914 Vibration dampening bushing A434-17 91433351301

914 Vibration dampening bushing A434-17 91433351301

This is a reproduction of the NLA vibration dampening bushing for the rear strut tower. Compare to 914 333 514 01. I am making another style also (click on detail for more info) $40 a set

914 window track rubber / fuzzey seals for late door

914 window track rubber / fuzzey seals for late door

These are the fuzzey seals tha the late style door uses to seal the front of the window track . Compare to 914.542.161.12. This 1 left and 1 right. $28

914 Wiring harnes snorkel tube

914 Wiring harnes snorkel tube

This is the part you need to seal the tunnel area behind the firewall to the engine tin. I made it long enough that it should fit most 6 applications, but will still work for the 4. Made from durable silicone.

914.424.224.03 late side shifter Firewall bushing

914.424.224.03 late side shifter Firewall bushing

This is the firewall bushing that will take some of the slop out of your shifting. Normally these are difficult to install, but we have made some changes that will allow for easy installation. We I decided to make these just like the small...

914.424.591.00 Parking brake sealing bellows - Set of 2

914.424.591.00 Parking brake sealing bellows - Set of 2

This i sthe barking barake bellows that the OEM one disolves in brake fluid. Now you can replace this hard to find part, inexpensively. This is a set of 2, because if you are missing one, you probably need or will need another soon.

914.424.592.00 Emergency Brake Bellows - Set of 2

914.424.592.00 Emergency Brake Bellows - Set of 2

Set of two Ebrake bellow boots. These are NLA 914.424.592.00.

914.572.913.10 Front trunk bulkheads sealing grommet set of 2

914.572.913.10 Front trunk bulkheads sealing grommet set of 2

This is a set of 2 new front trunk bulkhead seals. These are mostly deteriorated on many cars that have them. These will make an airtaight seal with new hoses. If you elect to us ethe OEM (paper and aluminum), you may want to trim the inner lip...

Airbox rebuild kit with late (grill type) top seal

Airbox rebuild kit with late (grill type) top seal

This is the seals you will need to rebuild the airbox flappers, and seal the bower unit to the upper section. It also includes the molder top seal that holds the grill in place. Others use a seal that is cut and glued in the corners for a fit...

Brake light / Trans reverse light switch cover 914.613.491.00

Brake light / Trans reverse light switch cover 914.613.491.00

This is the same boot for both application. Fits all years. These are currently availabe at over $20 each. Mine have the correct retaining grove at the base to make a good seal. Save yourself a bunch of cash and get a well made part. These are in...

Butyl Cord 9.5mm x 15'

Butyl Cord 9.5mm x 15'

This is the cord used by factory to seal the front windshield and rear glass.

Comes in a 15' roll

Caps for Ski Rack mounting holes (set of 6)

Caps for Ski Rack mounting holes (set of 6)

Caps to cover the mounting holes for factory ski racks

Cover cap for adjuster cover on ECU box

Cover cap for adjuster cover on ECU box

I didn't even know mine was missing until I checked. These are not being shown as available alone, so no suprice when they got lost or damaged they were never replaced. These are so inexpensive you almost can't afford not to. Yes the last picture...

Defroster seals (set of 2)

Defroster seals (set of 2)

Closed cell foam seals to replace the OEM ones that are not available

Early 911/944/356 and 914 Steering Pan Seal Set

Early 911/944/356  and 914 Steering Pan Seal Set

356 1950-59, 911 1965-73, 914 1970-76, 911 1984-86, 944 1985-88, 924 1986-88

Early bumper spacer "dog bones" set of all 4

Early bumper spacer "dog bones" set of all 4

Photos and Descriptions from 914rubber.com These are new spacers for the early bumpers. The isolate the body from the bumper and help keep the proper gap.
Now you can get a set of 4.

Early side shift firewall to housing gasket

Early side shift firewall to housing gasket

This is the tail shift gasket that holds the plastic housing to the firewall. This is only the "band" at the firewall.

 914.424.502.00

Early tail shift bellows 914.424.297.00 70-72

Early tail shift bellows 914.424.297.00 70-72

This is the bellows that fits perfectly on the plastic housing of your tail shift cover at the firewall.

Shown with the band that is available, but not included

Early Trans Rubber Bellows and Band for Plastic Housing

Early Trans Rubber Bellows and Band for Plastic Housing

 This is a set of both the band at the housing to firewall and the bellows on the firewall housing.

Parts 914.424.502.00 and 914.424.297.00

Engine Deck Lid Seal

Engine Deck Lid Seal

This is the "seal " that you see between the back glass and the deck lid. It hides the gap, and keeps water from rolling directly in the opening.

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

This is a drain tube that is located on the bottom of the front trunk in the 914 and is also used in the 911 light buckets. I designed the tube to be slightly more square at the base to help create a slightly more rigid base. This helps to keep...

Fuel line grommet 10mm

Fuel line grommet 10mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Fuel line grommet 8mm

Fuel line grommet 8mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Headlight bucket wiring anti chafing grommet material set of 2

Headlight bucket wiring anti chafing grommet material set of 2

This is a set of 2 enough for both sides.

Late Airbox Grill and seal

Late Airbox Grill and seal

This is the airbox seal and a new airbox grill used on later cars. It can be used to retrofit you early car if you so wish.

I do also sell the grills seporately if you need just a grill.

porsche 914 2.0 Throttle body gasket

porsche 914 2.0 Throttle body gasket

This is a reproduction 2.0 Throttle body gasket. OEM is no longer available.

Porsche 914 Clutch Cable Bellows 914.423.922.02

Porsche 914 Clutch Cable Bellows 914.423.922.02

Clucth cable bellows replace your old mangled or missing bellows for a fraction of the cost others charge. High quality.

Porsche 914 Firewall back pad

Porsche 914 Firewall back pad

This is a solution to the OEM back pad that absorbs water and will cause rust on the back firewall. It is precision cut using the OEM as a template. The material is fireresistant and has excellent sound deadning properties. It is soft as it is...

Porsche 914 Front Turn Signal Boot

Porsche 914 Front Turn Signal Boot

These are the 914 front turn signal boots that go from the body to the back of the signal housing. They are made from high temperature silicone and will hold up much better than OEM. Available as a set of 2 or individually.

Porsche 914 front turn signal boot ONE only

Porsche 914 front turn signal boot ONE only

This is asingle 914 front turn signal boot that go fromt the body to the back of the signal housing. They are made from high temp silicone and will hold up much better than OEM. OEM part number is 914.631.217.10 .

Porsche 914 heater cable nipple Set

Porsche 914 heater cable nipple Set

This listing is for a set of 2 heater cable covers or "nipples" that keep water from getting into the center tunnel from the firewall side. Most of these have baked out as they were made from organic rubber. I have made these from a higher temp...

Porsche 914 Maintence Manual in PDF format (CD)

Porsche 914 Maintence Manual in PDF format (CD)

This is a PDF formant of the maintence manuals for the 914

Rubber bumper to keep trunk from hitting deck lid

Rubber bumper to keep trunk from hitting deck lid

This is the NLA rubber "bumper" that keeps the rear trunk lid from hitting the engine deck lid. You will need the metal angle bracket that holds this in place, as it is not included.

Steering linkage "puck" 901.347.201.02

Steering linkage "puck" 901.347.201.02

This part is a vibration dampener. It actually flexes to help provide a smoother response to the steering wheel when going over a bumpy road. Others have made this part out of Delrin or aluminum, which is fine if you want t transfer all the...

Throttle body gasket for 1.7 intake

Throttle body gasket for 1.7 intake

This is a NLA gasket available only here only $10.50

Vent hose bushing 823823591 999.702.049.50 set of 2

Vent hose bushing 823823591  999.702.049.50 set of 2

Long extinct grommet in the firewal for the vent line into the charcoal canaster.

Also known as 823823591 999.702049.50

 

SET OF 2 

Windage Tray Oil Baffle Seal - Set of 4

Windage Tray Oil Baffle Seal - Set of 4

These are all new silicone windage tray seals. Don't forget to replace these when you rebuild your motor.

Windshield wiper Grommet set of all 4

Windshield wiper Grommet set of all 4

This listing is for a set of wiper grommets for your 911, 914, 924, 928, 930 or 944. These at list price would run you about $46 for the set. That's why many put off replacing these. Now you can replace all for a fraction of the price.

Wiper grommet male set of 2 901.628.924.00

Wiper grommet male set of 2 901.628.924.00

This is a listing for the male grommets in the wiper assembly. It is for a set of 2. These have application for 911, 924, 928, and 944's.