Nuts and Bolts

 

Early E-Brake spring 901.424.543.00

Early E-Brake spring 901.424.543.00

This spring is notorious for breaking and in careful evaluation we realized that the way the OEM part was made concentrated force right where they were breaking. We have made a design imprevement that will make these last longer than the OEM...

45 Degree Rubber Sleeve for Fuel Line

45 Degree Rubber Sleeve for Fuel Line

This grommet goes in the engine compartment tin where the fuel line passes through the the tin.

911.424.139.00 Ball cup for shifter at transmission

911.424.139.00 Ball cup for shifter at transmission

This is the ball cup that fits into the lever on the transmission that connects to the rod. Don't forget to check out the other related items as you may need them.

914 Clutch pulley assembly

914 Clutch pulley assembly

This is a custom machined Delrin Pulley with a new insert bushing.

914 CV bolt drilled for safety wire includes wave washer

914 CV bolt drilled for safety wire includes wave washer

This is a single new CV bolt machined for safety wire, with wave washer included. 16 required per car.

914 GT Headlight release cable assembly

914 GT Headlight release cable assembly

This is a kit that is used to replace your headlight motors. Nice way to reduce the weight if you are autocrossing or concerned about weight. Also just a neat kit if you want something different or are making a GT clone.

914 Headlight pivot bushings set of 4 enough for one car

914 Headlight pivot bushings set of 4 enough for one car

Headlight pivot bushings. These replace the old nylon ones that desintegrate. They go in the tube and interact with the metal brackets that mount to the body. We are doing up the arm bushings next and will have them in a few weeks.

914 Rocker panel rivets set of 12 + 2 extra

914 Rocker panel rivets set of 12 + 2 extra

This is a set of rocker panel rivets that you can use to attach the factory rocker panels for your 914. You need 6 per side, and we included 2 extra just in case.

They are black finished aluminum so they will not rust.

914.424.224.03 late side shifter Firewall bushing

914.424.224.03 late side shifter Firewall bushing

This is the firewall bushing that will take some of the slop out of your shifting. Normally these are difficult to install, but we have made some changes that will allow for easy installation. We I decided to make these just like the small...

914.628.012.55 mount for wiper assembly

914.628.012.55 mount for wiper assembly

This is the piece that is often damaged during removal as it's not easly seen. That is is it's still intact. 40 years of vibration has taken it's toll on most of these. Now you can replace yours. It is often purchased with the airbox rebuild kit...

914.722.021.10 Jack strap with hardward (stainless) set of 2

914.722.021.10 Jack strap with hardward (stainless) set of 2

Finally a high quality rubber part with hardware made to look like OEM, except it's stainless and will not rust like OEM!

914/6 dipstick for fender oil cooler

914/6 dipstick for fender oil cooler

Thsi is a replica of the factory 914/6 dipstick for the offset oils cooler in the fenderwell. They are not identical to factory close. We hand made each of these. Will start shipping 7/14/14 More pictues will be added as soon as they are back from finishing.

914/6 Stainless fuel rail

914/6 Stainless fuel rail

These are made at the request of a 914/6 owner that wanted the correct rail reproduced in stainless. they have been flow and pressure tested to meet (actually exceed) flow rates and pressures compared to the OEM. We may be out from time to time...

Barrel nut assembly (1)

Barrel nut assembly (1)

This is the barrel nut that is used for throttle cable and the heater flapper valves.

It is the nut and "barrel" that is used to bind the associated cable end.

Climate control knobs set of 3 - 1 red 2 black 901.571.917.00

Climate control knobs set of 3 - 1 red 2 black 901.571.917.00

Now you can buy these never available alone parts to spruce up your climate control quickly and inexpensively. This is a set of 3. One Red Two Black They were used on 911, 912, 914, and 930 models from 1965 to 1985.

Clutch Cable M7 Hexagon Nut - Stainless Steel

Clutch Cable M7 Hexagon Nut - Stainless Steel

This is the correct nut for your clutch cable. I recomend using 2 tightened against each other to lock them in place. Many have used Nylock nuts to replace the onle ones. I had a bad experiece where on a hot day mine got warm enough when I was...

Clutch cable trunion 911.423.205.03

Clutch cable trunion 911.423.205.03

This is for the glod plated clevis that the clutch cable slides through brand new now $6 all day long.

Color coded socket / wrench labels 1 sheet

Color coded socket / wrench labels 1 sheet

This is a sheet of labels that can be applied to your wrenches or sockets to easily identify see what each one is. Stampings are sometimes difficult to read under the car, but not you can see if they are odd or even just by the color od the...

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

Cylinder Head Temperature Sensor conforms to 0 280 130 012 Spec

This is a reproduction cylinder head temperature sensor that is construcetd from stainles steel. Utilizing tested internal componets that have been used to replace these (Original Customs was originally remanufacturing these). Now you can replace...

Engine deck lid base for pull 914.512.177.10

Engine deck lid base for pull 914.512.177.10

This is the machined base for the engine deck lid pull. It holds the back pad to the fireall in this area also.

Engine Deck Lid Bumper Set 914.559.253.10

Engine Deck Lid Bumper Set 914.559.253.10

These are the long sought after engine deck lid bumpers that are NLA. You can get them here and inexpensively.

 

Engine screw kit Stainless w/washer allen head

Engine screw kit Stainless w/washer allen head

This is a set of 50 allen head screws with washers that replace the original "cheesehead" screws. They are stainless with stainless washers. $20

Fuel filter only

Fuel filter only

This includes - The fuel filter This is the late front mounted fuel filter Note the picture with the fuel pump is for illustration only. The second picture is what is in the "kit" Please note ethanol will deterrorate the hoses pretty quickly with...

Fuel filter, and replacment hoses for "late" installation front

Fuel filter, and replacment hoses for "late" installation front

This includes - The fuel filter 1- 12mm hose from pump to filter 1- 7mm hose from filter to tank 1- 7mm pump to engine line (connect to pump and delivery to engine plastic line) 1- 7mm return to tank line (other plastic hose into tank) The 12mm...

Fuel line grommet 10mm

Fuel line grommet 10mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Fuel line grommet 8mm

Fuel line grommet 8mm

This listing is for a the fuel line grommet at the firewall where the fuel line enters the engine compartment. For quite some time we have had no choice other than to use a sandard sheetmetal grommet to keep the line from rubbing on the sheet...

Fuel Rail Hexagon Head Bolt with Sealing Ring - Stainless Steel

Fuel Rail Hexagon Head Bolt with Sealing Ring - Stainless Steel

A hard to find M4 X M8 bolt and washer for the 914's fuel rail.

Has application on all 914 stock fuel rails and some 1974-77 911 applications.

Mirror Base Screw Set - Stainless

This is a set of 2 mirror base screws, enough for one mirror. Sold in stainless steel so they will not rust.

Paint placard metal plate with 4 correct rivets Karman plate

Paint placard metal plate with 4 correct rivets Karman plate

If you are repainting your car this is the one plate you cant easily remove without destroying it. Now you can get a replacement plate and the rivets needed to replace it.

Porsche 914 clutch cable 914.423.401.05

Porsche 914 clutch cable 914.423.401.05

Clutch cable for 914 -4

Picture shows all of the other parts you may want, but this is for a clutch cable only.

Porsche 914 Door Panel Clips set of 18 - both doors

Porsche 914 Door Panel Clips set of 18 - both doors

These will fit any year of 914, note it's a full set of all 18 - Enough for both doors. 

Rubber hood bumper 999.703.036.50 (4) required per car

Rubber hood bumper 999.703.036.50 (4) required per car

These are the rubber bumpers that adjust up and down to create a positive stop for your hood.

(1)

Schnorr washers for CV joint bolts - individual part

Schnorr washers for CV joint bolts - individual part

Don't want to order a massive quantity of these to sit on your shelf forever. Now you can order only what you want.

Use our first class mail option to save shipping cost as these are small.

Schorr washer for CV joint - each

Schorr washer for CV joint - each

Now you can get exactly how many you need without having a lifetime supply of these. Quantity is each.

Try shipping media mail to save on shipping

Seat adjuster rebuild kit for one car and special tool included

Seat adjuster rebuild kit for one car and special tool included

This kit is enough to do 2 seats or one car. It includes 2 of each bushing 2 drive pins and the special tool you will want.

Side marker plasic clip to hold the base to the body- 4 req /car

Side marker plasic clip to hold the base to the body- 4 req /car

These are the clips that hold the base to the car body and often break. Sold individualy, so if you need a full set for your car you will need 4.

Special tool for drive pins - seat adjuster applicatiom SPT900

Special tool for drive pins - seat adjuster applicatiom SPT900

This is a special tool to install drive pins. It allows you to center the pin and use a hammer to wedge the pin in.

Speednut set of 14 for letters

Speednut set of 14 for letters

This is a complete set of 14 speednuts that can be used to attach the letters to the grill.

Steering linkage "puck" 901.347.201.02

Steering linkage "puck" 901.347.201.02

This part is a vibration dampener. It actually flexes to help provide a smoother response to the steering wheel when going over a bumpy road. Others have made this part out of Delrin or aluminum, which is fine if you want t transfer all the...

Visor cores for rebuild service

These are cores fo r our visor rebuild service. We charge $75 for cores because we want them back. Please note that you will want to strip down and return your cores (we charge $25 to strip them). You will also need to check the screw bases to...

Wirring hold down cover. Correct gloss fits well per 1'

Wirring hold down cover. Correct gloss fits well per 1'

We faithfully recreated the wiring harness hold down material. Others will sell you shrink tube and yes you can make it work, but it's not right. Ours fits and is actually a soft rubber with correct gloss level and it actually grips and holds well. It takes about 9' for every hold down on car.