Pedal System, Cables and Levers

 

914 Bump Shift Knob 5 Speed

914 patern shown standard to see 911 bump click on zoom

This shift knob is very close to OEM, only the plastic is different. It is hand finished and has an inlay just like OEM.

 

Part number 901.424.014.00

Shifter Crush "Gasket" 999.532.003.00

Shifter Crush "Gasket" 999.532.003.00

This is an OEM crush gasket that is used to hold your shifter in place.

901.741.291.00 Tail shift sealing sleeve #50 on the PET

901.741.291.00 Tail shift sealing sleeve #50 on the PET

This is the rear sealling bellows for the early side shift transmission. PET catalog shows part as 901.741.291.00. Interestingly enough others reference this as Speedometer Cable Boot Fits 911, 1965-1971. This was reproduced off a stock 914 part...

914-6 hand throttle replica - for carbed cars - or AX

914-6 hand throttle replica - for carbed cars - or AX

This is a replica of the 916 hand throttle used to help set the "choke" when the car is warming up. or if you want to maintain a higher base RPM for A/X.

Side shift 914 and 911 knuckle bushings set 911 424 223 03

Side shift 914 and 911 knuckle bushings set 911 424 223 03

These are the bushings for the late coupler on the side shift linkage. These are toleranced correctly so they fit snug and are easier to install. Looks like these are part # 911.424.223.03. I had ordered new from factory and they were sloppy....

911.424.139.00 Ball cup for shifter at transmission

911.424.139.00 Ball cup for shifter at transmission

This is the ball cup that fits into the lever on the transmission that connects to the rod. Don't forget to check out the other related items as you may need them.

Early tail shift bellows 914.424.297.00 70-72

Early tail shift bellows 914.424.297.00 70-72

This is the bellows that fits perfectly on the plastic housing of your tail shift cover at the firewall.

Shown with the band that is available, but not included

Early side shift firewall to housing gasket

Early side shift firewall to housing gasket

This is the tail shift gasket that holds the plastic housing to the firewall. This is only the "band" at the firewall.

 914.424.502.00

Late side shifter bushing for transmission mount 914.424.224.02

Late side shifter bushing for transmission mount 914.424.224.02

This is the bushing that installs at the mount on the transmission to guide the lever for a more solid shift.

914 late side shifter bellows

914 late side shifter bellows

Yes 2 are shown, but you only need one. This is the bellows that goes at the rear of the shift linkage and keeps crud from getting into the shifter housing (the black plastic cup).

They were NLA, but you can get them here.

Late Side Shift Bushing Kit

Late Side Shift Bushing Kit

Get everything you need to eliminate sloppy shifting in one kit, with the option to add the shift housing cover for only $12 more. Kit consists of: 911.424.139.00 911.424.223.03 (x2), 911.424.224.02, 911.424.224.03, and 914 424 239 02.

914.424.224.03 late side shifter Firewall bushing

914.424.224.03 late side shifter Firewall bushing

This is the firewall bushing that will take some of the slop out of your shifting. Normally these are difficult to install, but we have made some changes that will allow for easy installation. We I decided to make these just like the small...

PCG 424.501.01 Late side shifter cover

PCG 424.501.01 Late side shifter cover

This is the cover that keep the crud from gettining into the shift mechanism atthe rear of the linkage. It mounts onto a plate atthe transmission. It is a nice part to finish off your underside ans it's nice and glossy. It is also flexable...

Span Band for late side shifter cover 914.424.503.01 Repro

Span Band for late side shifter cover 914.424.503.01 Repro

This is the NLA "Span Band" that is used to tension the cover at the transmission.

914 Leather Shift Boot

914 Leather Shift Boot

This is a shift lever boot made from leather that is used in the appearance group consoles.

Clutch cable trunion 911.423.205.03

Clutch cable trunion 911.423.205.03

This is for the glod plated clevis that the clutch cable slides through brand new now $6 all day long.

Porsche 914 clutch cable 914.423.401.05

Porsche 914 clutch cable 914.423.401.05

Clutch cable for 914 -4

Picture shows all of the other parts you may want, but this is for a clutch cable only.

Porsche 914 Clutch Cable Bellows 914.423.922.02

Porsche 914 Clutch Cable Bellows 914.423.922.02

Clucth cable bellows replace your old mangled or missing bellows for a fraction of the cost others charge. High quality.

Clutch cable end (trunion), bellows, 2 nuts, pulley and bushing

Clutch cable end (trunion), bellows, 2 nuts, pulley and bushing

This is a package that includes the Clutch cable end that attaches to the throwout bearing arm, the bellows that keeps crud out of the cable tube, the pulley, pulley bushing and 2 correct nuts to set tension. Others will sell you a nylock nut. It...

Clutch Cable M7 Hexagon Nut - Stainless Steel

Clutch Cable M7 Hexagon Nut - Stainless Steel

This is the correct nut for your clutch cable. I recomend using 2 tightened against each other to lock them in place. Many have used Nylock nuts to replace the onle ones. I had a bad experiece where on a hot day mine got warm enough when I was...

914 heater lever knob - Red

914 heater lever knob - Red

This is a direct

replacement for your faded or beat up heater lever. Simply screws on after the old one screws off.

PCG42407501 914 heater cable for 914/6

PCG42407501 914 heater cable for 914/6

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

914.424.075.02.NC 914 heater cable for 70-74 (NOT 914/6)

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

914.424.075.03 914 heater cable for 75-76

914.424.075.03 914 heater cable for 75-76

This is a reproduction of a factory 914 heater cable that was made from an OEM part. Like the OEM we added an anti abrasion coating to keep metal from metal contact in the heater tubes. We offer you the option to purchase without in the...

Porsche 914 heater cable nipple Set

Porsche 914 heater cable nipple Set

This listing is for a set of 2 heater cable covers or "nipples" that keep water from getting into the center tunnel from the firewall side. Most of these have baked out as they were made from organic rubber. I have made these from a higher temp...

Early E-Brake spring 901.424.543.00

Early E-Brake spring 901.424.543.00

This spring is notorious for breaking and in careful evaluation we realized that the way the OEM part was made concentrated force right where they were breaking. We have made a design imprevement that will make these last longer than the OEM...

914.424.592.00 Emergency Brake Bellows - Set of 2

914.424.592.00 Emergency Brake Bellows - Set of 2

Set of two Ebrake bellow boots. These are NLA 914.424.592.00.

914.424.591.00 Parking brake sealing bellows - Set of 2

914.424.591.00 Parking brake sealing bellows - Set of 2

This i sthe barking barake bellows that the OEM one disolves in brake fluid. Now you can replace this hard to find part, inexpensively. This is a set of 2, because if you are missing one, you probably need or will need another soon.

Brake light / Trans reverse light switch cover 914.613.491.00

Brake light / Trans reverse light switch cover 914.613.491.00

This is the same boot for both application. Fits all years. These are currently availabe at over $20 each. Mine have the correct retaining grove at the base to make a good seal. Save yourself a bunch of cash and get a well made part. These are in...

Gas pedal package with clutch and brake rubber covers

Gas pedal package with clutch and brake rubber covers

This package is fro a new gas pedal along with the clutch and brake pad rubber covers.  You get all 3 pcs. 

914 Front trunk cable - Cable only

914 Front trunk cable - Cable only

This is the front trunk cable only for the 914. It is a direct replacement for the OEM. These usually fail at the attachmnet point in the release mechanism. Making the cable just a little too short. Both the engine deck lid cable and the front...

914 Rear deck lid relaease cable

914 Rear deck lid relaease cable

This is a direct replacement for the rear deck cable cable, it has a threadded termination that will screw right into the handle base to allow you to pull. This typically fails at the latch portion where the stress is at the termination there. I...