Trunk seals

914 Engine deck lid welting enough for all 3 sections

914 Engine deck lid welting enough for all 3 sections

This is the rubber "gasket" seal that isolates the grill from the body and deck lid. Most of these have been pained over or ar in very poor repair. Now you can replace all 3 sections cheap. NLA OEM

914 Eyebrow grommets set of 6

914 Eyebrow grommets set of 6

This is a set of all 6 grommets you will need to install the eye lid metal at the base of the headlight bucket. I made these slightly easier to install.

914 Fresh air box top seal (SEAL ONLY)- Late for use with grill

914 Fresh air box top seal (SEAL ONLY)- Late for use with  grill

This is the seal that goes on the top of the airbox that holds the grill in place. The early cars do not have the grills but you can add one by changing out this seal and including a new plastic grill.

 

914 Front trunk Bulkhead seal

Same as set only excludes main seal

This is the upper "bulkhead seal" infront of the gas tank that runs from strut to strut. Available without buying the entire set. $18 compare to OEM at $50, only mine has an aluminum clip and is slightly taller for a better seal.

914 Front trunk cable - Cable only

914 Front trunk cable - Cable only

This is the front trunk cable only for the 914. It is a direct replacement for the OEM. These usually fail at the attachmnet point in the release mechanism. Making the cable just a little too short. Both the engine deck lid cable and the front...

914 Front trunk plugs set of 9

914 Front trunk plugs set of 9

This is a full set all 9 of the front trunk plugs. For the holes that were in the cars til late 75. They are made from silicone and make a good seal.

914 Front trunk seal set to new OEM profile

914 Front trunk seal set to new OEM profile

This is a set of the main front trunk seal and the upper bulkhead seal. It is not like OEM only the corneres are actually molded into the complete seal. This makes them permanently bonded and will not seporate like the OEM does. It is NOT a...

(1)

914 Jack strap -Rubber only set of 2

914 Jack strap -Rubber only set of 2

These are the new formulation more flexable jack strap rubber. While the straps do not display the pat number on them are are equivalent to the OEM parts. This listing is for a set of 2 pieces as shown.

914 Rear deck lid relaease cable

914 Rear deck lid relaease cable

This is a direct replacement for the rear deck cable cable, it has a threadded termination that will screw right into the handle base to allow you to pull. This typically fails at the latch portion where the stress is at the termination there. I...

914 Rear main trunk seal only

914 Rear main trunk seal only

This is the rear main trunks seal only. This has the aluminum clip (not steel like OEM). I have these listed as a set for a better value, but if you need only the lower, this is your listing.

914 rear sway bar bushing set of 2 90133379304

914 rear sway bar bushing set of 2 90133379304

These are the new thermally enhanced rear sway bar bushings, I include both, think about it, do you really only want to replace one? These have been NLA for quite some time and I have been hand casting these. The quality is vastly improved. The...

914 rear tail light lens seal

914 rear tail light lens seal

This is a set of soft silicone cords that are used to seal the lens to the housing. These ARE NOT the seal between the body and housing.

914 Rear Trunk Bulkhead Seal

914 Rear Trunk Bulkhead Seal

This is the seal that keeps water from rolling back into the trunk from the engine compartment. It is critical to keeping your trunk dry. Slightly taller than OEM but creates a much better seal.

914 Rear trunk carpet

914 Rear trunk carpet

This is a Perlon trunk liner that is without edgebinding. If you wish to have the edges bound It is an additional $30

914 Rear trunk Lid Guide Bushing

914 Rear trunk Lid Guide Bushing

This part is the one that holds the spring in place on the rear trunk locking guide pin. This was only available as an assembly previously. Only $9.99

914 Rear Trunk seal set - Upper and lower

914 Rear Trunk seal set - Upper and lower

This a set of rear trunk seals. The upper is taller and has a profile that will close the gap on the larger opening. The lower is a short seal with a double fin to help assure a good seal $48

914 Tail Light Gasket Set

914 Tail Light Gasket Set

These are the gaskets that go between the body and the tail light assembly. This is a set of 2. Only $24

914 Targa Top Latch Cups Set 914.559.227.10

914 Targa Top Latch Cups Set 914.559.227.10

This is a set of the targa latch cups that are in the trunk area. They are factory correct and yes made my me. These are not a cheap URO part. You can even by for less from me!

914 Trunk lock gasket

914 Trunk lock gasket

These are a reproduction of the OEM version, only they actually seal. OEM was a plastic that didn't actually seal. Mine is a soft silicone that seals and will actually help heep water out of your trunk. At this price, you really can't not replace it.

914 Upper Rear Trunk Roof Holder

914 Upper Rear Trunk Roof Holder

This is the plastic roof holder that goes in the front of the rear trunk. The roof sits on it at the top, this is the other part you will need if you are replacing all the rear trunk hardware. $6.40 each (sold individually)

914.572.913.10 Front trunk bulkheads sealing grommet set of 2

914.572.913.10 Front trunk bulkheads sealing grommet set of 2

This is a set of 2 new front trunk bulkhead seals. These are mostly deteriorated on many cars that have them. These will make an airtaight seal with new hoses. If you elect to us ethe OEM (paper and aluminum), you may want to trim the inner lip...

914.628.012.55 mount for wiper assembly

914.628.012.55 mount for wiper assembly

This is the piece that is often damaged during removal as it's not easly seen. That is is it's still intact. 40 years of vibration has taken it's toll on most of these. Now you can replace yours. It is often purchased with the airbox rebuild kit...

914.722.021.10 Jack strap with hardward (stainless) set of 2

914.722.021.10 Jack strap with hardward (stainless) set of 2

Finally a high quality rubber part with hardware made to look like OEM, except it's stainless and will not rust like OEM!

Airbox drain tubes set of 3 PCG 571 900 00

Airbox drain tubes set of 3 PCG 571 900 00

These are the air box drain tubes NOT sourced at your local hardware store. They are actually ribbed and make a very firm attachment onto the fittings. The T fitting is shown on the assembly, however, it is NOT included.

Airbox rebuild kit with late (grill type) top seal

Airbox rebuild kit with late (grill type) top seal

This is the seals you will need to rebuild the airbox flappers, and seal the bower unit to the upper section. It also includes the molder top seal that holds the grill in place. Others use a seal that is cut and glued in the corners for a fit...

Engine Deck Lid Seal

Engine Deck Lid Seal

This is the "seal " that you see between the back glass and the deck lid. It hides the gap, and keeps water from rolling directly in the opening.

Front trunk carpet kit - with plywood insert

Front trunk carpet kit - with plywood insert

This is a two piece front trunk kit made of perlon. It unilke others mine comes with the plywood attached so you can drop it in. Includes the tire board and comes in Black or Charcoal. Selcet no board to get jsut the perlon and re use your board.

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

This is a drain tube that is located on the bottom of the front trunk in the 914 and is also used in the 911 light buckets. I designed the tube to be slightly more square at the base to help create a slightly more rigid base. This helps to keep...

Front trunk guide tube and pull cable

Front trunk guide tube and pull cable

This is a set of the front trunk release tube and the pull cable that goes in it. If your tube is cracked it allows the wire to flex making it dificult to open the front trunk. They were NLA from factory for some time so I decided to make them....

Front trunk guide tube only (NO CABLEINCLUDED)

Front trunk guide tube only (NO CABLEINCLUDED)

This is for the front trunk guide tube only. The cable is shon in the picture BUT IS NOT INCLUDED.

I listed this for people that just need the tube.

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

This is our new reproduction front trunk seal with the OEM profile. It has softer corners to help the trunk to seat better than OEM. SHOWN WITH OPTIONAL BULKHEAD SEAL

(1)

Headlight bucket wiring anti chafing grommet material set of 2

Headlight bucket wiring anti chafing grommet material set of 2

This is a set of 2 enough for both sides.

Porsche 914 Firewall back pad

Porsche 914 Firewall back pad

This is a solution to the OEM back pad that absorbs water and will cause rust on the back firewall. It is precision cut using the OEM as a template. The material is fireresistant and has excellent sound deadning properties. It is soft as it is...

Rubber bumper to keep trunk from hitting deck lid

Rubber bumper to keep trunk from hitting deck lid

This is the NLA rubber "bumper" that keeps the rear trunk lid from hitting the engine deck lid. You will need the metal angle bracket that holds this in place, as it is not included.

Rubber hood bumper 999.703.036.50 (4) required per car

Rubber hood bumper 999.703.036.50 (4) required per car

These are the rubber bumpers that adjust up and down to create a positive stop for your hood.

(1)

Wiper grommet male set of 2 901.628.924.00

Wiper grommet male set of 2 901.628.924.00

This is a listing for the male grommets in the wiper assembly. It is for a set of 2. These have application for 911, 924, 928, and 944's.

Wirring hold down cover. Correct gloss fits well per 1'

Wirring hold down cover. Correct gloss fits well per 1'

We faithfully recreated the wiring harness hold down material. Others will sell you shrink tube and yes you can make it work, but it's not right. Ours fits and is actually a soft rubber with correct gloss level and it actually grips and holds well. It takes about 9' for every hold down on car.