Weather Stripping

914 Fog light gaskets set of 2 (enough for one car)

914 Fog light gaskets set of 2 (enough for one car)

This is a fog light gasket that replaces the crusty OEM ones you've probably had in since the car was new. $15 a set.

Not the lens portectors can be bought with for an additional savings! Shown but not included unless you select the option.

914 Front trunk plugs set of 9

914 Front trunk plugs set of 9

This is a full set all 9 of the front trunk plugs. For the holes that were in the cars til late 75. They are made from silicone and make a good seal.

914 Eyebrow grommets set of 6

914 Eyebrow grommets set of 6

This is a set of all 6 grommets you will need to install the eye lid metal at the base of the headlight bucket. I made these slightly easier to install.

New OEM style front turn signal seals set of 2

New OEM style front turn signal seals set of 2

Molded from a high quality rubber, these seals are one piece and fit directly to the housing just like OEM.

Porsche 914 front turn signal boot ONE only

Porsche 914 front turn signal boot ONE only

This is asingle 914 front turn signal boot that go fromt the body to the back of the signal housing. They are made from high temp silicone and will hold up much better than OEM. OEM part number is 914.631.217.10 .

Porsche 914 Front Turn Signal Boot

Porsche 914 Front Turn Signal Boot

These are the 914 front turn signal boots that go from the body to the back of the signal housing. They are made from high temperature silicone and will hold up much better than OEM. Available as a set of 2 or individually.

914 Side marker lens seal kit (set of 2)

914 Side marker lens seal kit (set of 2)

These have been improved over the original design. They are constructed from soft neoprene, and have been designed to actually fit the lens correctly. Note the undercut relief for the inner edge of the seal. You will not find a better seal. These fit like OEM, only better.

914 Side marker electrical boot 914.631.218.10 set of 2

914 Side marker electrical boot 914.631.218.10 set of 2

Now you can get a set of 2 quality reproduction side marker lens caps. These seal the crud out and help to minimize corrosion of the contacts. As these see all the elements they are a critical seal. Now you can replace your brittle or missing...

Engine Deck Lid Bumper Set 914.559.253.10

Engine Deck Lid Bumper Set 914.559.253.10

These are the long sought after engine deck lid bumpers that are NLA. You can get them here and inexpensively.

 

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

Front Trunk Drain Tube (914) Light Bucket Drain 911 Application

This is a drain tube that is located on the bottom of the front trunk in the 914 and is also used in the 911 light buckets. I designed the tube to be slightly more square at the base to help create a slightly more rigid base. This helps to keep...

Early 911/944/356 and 914 Steering Pan Seal Set

Early 911/944/356  and 914 Steering Pan Seal Set

356 1950-59, 911 1965-73, 914 1970-76, 911 1984-86, 944 1985-88, 924 1986-88

Brake light / Trans reverse light switch cover 914.613.491.00

Brake light / Trans reverse light switch cover 914.613.491.00

This is the same boot for both application. Fits all years. These are currently availabe at over $20 each. Mine have the correct retaining grove at the base to make a good seal. Save yourself a bunch of cash and get a well made part. These are in...

914 Front trunk Bulkhead seal

Same as set only excludes main seal

This is the upper "bulkhead seal" infront of the gas tank that runs from strut to strut. Available without buying the entire set. $18 compare to OEM at $50, only mine has an aluminum clip and is slightly taller for a better seal.

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

Front trunk seal only - NEW OEM PROFILE best fit 914.51190110

This is our new reproduction front trunk seal with the OEM profile. It has softer corners to help the trunk to seat better than OEM. SHOWN WITH OPTIONAL BULKHEAD SEAL

(1)

914 Fresh air box top seal (SEAL ONLY)- Late for use with grill

914 Fresh air box top seal (SEAL ONLY)- Late for use with  grill

This is the seal that goes on the top of the airbox that holds the grill in place. The early cars do not have the grills but you can add one by changing out this seal and including a new plastic grill.

 

Late Airbox Grill and seal

Late Airbox Grill and seal

This is the airbox seal and a new airbox grill used on later cars. It can be used to retrofit you early car if you so wish.

I do also sell the grills seporately if you need just a grill.

901-628-923-01 Wiper Grommet Female - Set of 2

901-628-923-01 Wiper Grommet Female - Set of 2

This is a gasket that has been way overpriced for too long. Help me make these and other more afordable parts with your purchase today!

 

part number 901.628.923.01

Wiper grommet male set of 2 901.628.924.00

Wiper grommet male set of 2 901.628.924.00

This is a listing for the male grommets in the wiper assembly. It is for a set of 2. These have application for 911, 924, 928, and 944's.

914 Fender to cowl seals

914 Fender to cowl seals

These are the 2 short seals that close the gap between the fender and the cowl edge. Sold as a set of 2.

914 Windshield chrome trim all 3 pieces-Chrome color

914 Windshield chrome trim all 3 pieces-Chrome color

This is a set of all 3 windshield chrome pieces. Chrome in color. Shipped in a custom box designed to fit and provide protection. . There is a limited quantity available.

Butyl Cord 9.5mm x 15'

Butyl Cord 9.5mm x 15'

This is the cord used by factory to seal the front windshield and rear glass.

Comes in a 15' roll

914 Windshield to Dash Seal

914 Windshield to Dash Seal

This is a replacement for the seal that meets at the windshield and covers the dash pad vinyl. It's a cosmetic seal, but most are cracked as the steel inside has rusted. Can be installed without removing the windshield.

914 Main Targa Seal Reproduction

Upper main seal. Note the gap below the seal, the lower targa seal goes there.

This seal is just like like the OEM and has molded rubber corner blocks that connect to the side seals. The sides are molded to fit the corner bend at the top of the windshield (like OEM), and are bonded together. Fits all years.

914 Targa to Window Seal - Set of 2

914 Targa to Window Seal - Set of 2

A set containing both passenger and driver side seals mitered to fit snugly in the corner with the "vertical" targa seals. They have the outer "fin".

914 Lower Front Targa Seal

914 Lower Front Targa Seal

This is NOT the 3 part seal that goes along the top and sides of the front windscreen. it is the one below it. It is an important barrier in the fight to keep out water. Compare to OEM Part #914-563-319-10 and List of $140

914 Rear Targa Seal with Fuzzy Strip - OEM Profile

914 Rear Targa Seal with Fuzzy Strip - OEM Profile

This is my new and improved version of the rear targa seal. It has the OEM profile and even the fuzzy on the contact edge to prevent squeaking. This part is held in place with the OEM metal strips. 

914 Rear Targa Seal

914 Rear Targa Seal

Rear Targa Seal for 914. Attaches to roof. Has self adhesive waterproof tape to assure fit. 

914 Vertical Targa Seal - Set of 2

914 Vertical Targa Seal - Set of 2

These are similar to the OEM seals as they have a lip that the window rolls up against to keep water from entering the interior. Compare to OEM part numbers 914-531-143-10 and 914-531-144-10.

914 Triangle Window Seal - Set of 2

914 Triangle Window Seal - Set of 2

Slightly larger than OEM to fill the gap between the vertical bar and the door panel, with a more refined edge for a cleaner install.

914 Outer Door Seal - Set of 2

914 Outer Door Seal - Set of 2

These are the outer door seals that run in the tracks on the door itself. Unlike the OEM Part these are made of a solid marine grade rubber. Thanks to this change water no longer gets trapped in the channel and minimizes corrosion around the seal.

914 Inner Door Seal Set

914 Inner Door Seal Set

Inner door seal set. These attach to body with clip. Channel is reinforced with aluminum. They will not rust like factory seals. OEM lists at over $130

914 Outer door fuzzeys set of 2

914 Outer door fuzzeys set of 2

These are the metal strips with the outer Fuzzey that secure into the aluminum track on the outside edge of the door. set of 2. $29

914 Inner door fuzzeys set of 2

914 Inner door fuzzeys set of 2

These are the ones that go on the inside track and can be replaced without any dissasembly of the door. (set of 2)$38.

914 window track rubber / fuzzey seals for late door

914 window track rubber / fuzzey seals for late door

These are the fuzzey seals tha the late style door uses to seal the front of the window track . Compare to 914.542.161.12. This 1 left and 1 right. $28

914 Early Outer Door Scraper Set - Correct for 914/6 Application

914 Early Outer Door Scraper Set - Correct for 914/6 Application

These are the outer scrapers that the profile was originally designed for this car. To cut costs they were replaced in later production with the profile used on the 911. Ever wonder why they seem to grab? The later seals were not designed for this

914 Outer Window Scraper Seal Set

914 Outer Window Scraper Seal Set

These are the "scraper" seals that fit in the window tracks on the outside. It "scrapes" the window as it rolls down and up. Sold as a set.

914 Late door end cap set left and right

914 Late door end cap set left and right

These are reproductions of the OEM no longer available from factory. This is a set left and right. Compare to part # Left -914.542.173.10 Right-914.542.173.10

914 Early door end caps

914 Early door end caps

These are reproductions of the no longer available early door end caps, These have been reproducted in rubber for an easier fit. $32

914 Door Light Rubber Gasket - Set of 2

914 Door Light Rubber Gasket - Set of 2

Gasket for the door position sensor that operates the interior dome light.

914 Door handle gaskets

914 Door handle gaskets

These are the 4 pieces of rubber that isolate the handle formr the painted body. 2 for each side, This will do one car.

914 Mirror Base Gasket

914 Mirror Base Gasket

Mirror base gasket. This is one piece, goes between the mirror and the door.

rear window reseal kit

rear window reseal kit

If your window is leaking or loose and rattling around this is the kit that you will need to reseal it. It includes the 10mm sealing butyl rubber and the 2 setting blocks that are needed to isolate the window from the body. It will require you to...

Porsche 914 Jack hole plug

Porsche 914 Jack hole plug

Jack hole plug - you need 2 of these to do one car. 91455926710 is the part number. These are OEM. There are 2 in the picture, You will need to order 2 to get 2.

Engine Deck Lid Seal

Engine Deck Lid Seal

This is the "seal " that you see between the back glass and the deck lid. It hides the gap, and keeps water from rolling directly in the opening.

914 Engine deck lid edge protectors

914 Engine deck lid edge protectors

This is a set of all 3 edge pieces that keep the metal edges covered.

914 Engine deck lid welting enough for all 3 sections

914 Engine deck lid welting enough for all 3 sections

This is the rubber "gasket" seal that isolates the grill from the body and deck lid. Most of these have been pained over or ar in very poor repair. Now you can replace all 3 sections cheap. NLA OEM

914 Engine seal set of all 4

914 Engine seal set of all 4

This is your best value for all 4 seals. These replace the seals that help keep all the hot air from rising into the engine compartment, robbing your engine of horse power. Compare to 914-504-117-10 rear 914-504-155-10 sides and front.

Early side shift firewall to housing gasket

Early side shift firewall to housing gasket

This is the tail shift gasket that holds the plastic housing to the firewall. This is only the "band" at the firewall.

 914.424.502.00

914 Rear main trunk seal only

914 Rear main trunk seal only

This is the rear main trunks seal only. This has the aluminum clip (not steel like OEM). I have these listed as a set for a better value, but if you need only the lower, this is your listing.

914 Rear Trunk seal set - Upper and lower

914 Rear Trunk seal set - Upper and lower

This a set of rear trunk seals. The upper is taller and has a profile that will close the gap on the larger opening. The lower is a short seal with a double fin to help assure a good seal $48

914 Rear Trunk Bulkhead Seal

914 Rear Trunk Bulkhead Seal

This is the seal that keeps water from rolling back into the trunk from the engine compartment. It is critical to keeping your trunk dry. Slightly taller than OEM but creates a much better seal.

914 Trunk lock gasket

914 Trunk lock gasket

These are a reproduction of the OEM version, only they actually seal. OEM was a plastic that didn't actually seal. Mine is a soft silicone that seals and will actually help heep water out of your trunk. At this price, you really can't not replace it.

914 Tail Light Gasket Set

914 Tail Light Gasket Set

These are the gaskets that go between the body and the tail light assembly. This is a set of 2. Only $24

914 rear tail light lens seal

914 rear tail light lens seal

This is a set of soft silicone cords that are used to seal the lens to the housing. These ARE NOT the seal between the body and housing.

Fender liners set of 4 with mount clips

Fender liners set of 4 with mount clips

This is a set of fender liners that will help keep the crud from building up in the crevices that are known to harbor rust and keey more from being applied.

If you have a daily driver these are a must.

(1)

Rear licence plate light - rubber only

Rear licence plate light - rubber only

This is the rubber only for the rear license plate lights. It is one piece only. You can use this to reassemble your old lights. Here's a thread where Craig at Camp 914 rebuilt his using these rubber parts http://www.914world.com/bbs2/index.php?showtopic=252567&hl=rubber+rear+light